Войти:
Оценок - , средний балл: ( )

Инструкция по эксплуатации FUNAI, модель TVCR9G1

Производитель: FUNAI
Размер: 10.79 mb
Название файла: b0e8e80b-9760-4501-8557-aa328d8b335a.pdf

Язык инструкции:en

Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста

Фрагмент инструкции


(If necessary, rewind or fast forward the tape to the point at which you want to begin recording.) NORMAL RECORDING You can only watch the same TV program that is being recorded. 1 Select the channel to be recorded Press number buttons on the remote control or the CH Y or A button. r A CH 10 2 Select the tape speed { N Press SPEED button to select the desired tape speed (SP/LP/ SLP). SP 3 Begin recording REC Press RECORD button. The REC indicator flashes. SP v y 4 Stop recording Press STOP button when recording is completed. SKIPPING SOME MATERIALS DURING RECORDING Press PAUSE/STILL button to ->. temporarily stop recording. The ..... REC indicator flashes. Press PAUSE/STILL or RECORD button to resume record- sp ^_/ mg. NOTES: • To prevent tape damage, after five minutes, the TV/VCR will automatically return to the Recording mode. • When in the Pause/Still mode, a display showing 5 "I" marks will appear on the screen. Each "I" mark represents one minute of Pause time. You may refer to this display for remaining pause time available. • If "CLOSED CAPTION IONJ" is selected from the "CLOSED CAPTION SET UP" menu, the On Screen Display will appear for 5 seconds, then disappear. If you want to check the remaining pause time available using the On Screen Display, press DISPLAY button. The On Screen Display will appear for 5 seconds. -22- EN 7A08 COPYING A VIDEO CASSETTE (Requires another VCR) OTR (One Touch Recording) This function enables you to set a recording length simply by pressing REC/OTR button on the TV/VCR. Make sure... • Power must be turned on. • Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.) NOTE:This function cannot be done by the remote control. 1 Select the channel to be recorded Press the number buttons on the remote control or the CHANNEL ▼ or ▲ button. 2 Begin OTR Press REC/OTR button on the TV/VCR as many times as needed. The recording length will be determined by the number of times you press REC/OTR button. Each additional push will increase the recording time by 30 minutes. It is set up to 8 hours. Push(es) Display Recording length 1 push (normal recording) 2 pushes 0:30 30 minutes 3 pushes 1:00 60 minutes i i i 17 pushes 8:00 480 minutes HINTS: • Recording starts immediately when the REC/OTR button is pressed. • When REC/OTR button is pressed 18 times, the TV/VCR will switch to the Normal Recording mode. • To stop the OTR operation, press STOP button on the TV/VCR or on the remote control. • To show the remaining time, press DISPLAY button repeatedly until "OTR" appears on the TV screen. • Recording stops when 0:00 is reached. • Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T-120). • If the tape runs out before the end time, the TV/VCR will switch to the Stop mode immediately, eject the tape and the TV/VCR power will be turned off. You can make copies of video tapes made by friends or relatives for your enjoyment. WARNING: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect your TV/VCR and a Source (Playing) VCR using the following diagram. 1) Insert a pre-recorded video cassette into the Source (Playing) VCR. 2) Insert a blank video cassette, or one you want to record over, into the TV/VCR’s cassette compartment. 3) Press SPEED button to select the desired recording speed (SP, LP or SLP). 4) Press CHANNEL ▲ or ▼ button repeatedly so that "AUX" appears on the screen. 5) Begin playback of the tape in the Source (Playing) VCR. 6) Press RECORD button on the TV/VCR. NOTE: For best results during dubbing, use the TV/VCR’s front panel controls whenever possible. The remote control might affect the Source (Playing) VCR’s playback operation. [The TV/VCR] [Ex: Source (Playing) VCR] Audio/Video adapter cord (not supplied) VIDEO <® 0 OUT IK <© © AUDIO -23- EN 7A08 TIMER AUTOMATIC TIMER RECORDING You may set the TV/VCR to record while you are away. You can set 8 programs to record on a specific day, daily or weekly within a 1 year period. In the example below, the timer is being set to record: DATE: MAY 6th, 1997 SETTING TIME: from 7:30PM to 8:50PM CHANNEL: CH61 TAPE SPEED: LP NOTES: • You must use the remote control for this procedure. • If a cable box or satellite box is connected with the TV/VCR you will be limited to record only one channel. And the channel selector on the TV/VCR must be selected to the output channel of the boxes 3 or 4 and then the actual channel to be recorded must be selected on the boxes. Make sure... • Be sure the clock is set to the correct time and date before setting the timer. • Power must be turn on to set automatic timer recording. • Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or f...

Эта инструкция также подходит к моделям:
Телевизоры - W9TVCRG (10.79 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории