Plug the welder into the proper power supply receptacle. Flux Core Wire Installation Welding power may be applied to the output terminals, feed roll, work clamp, gun cable connection and welding wire even when the the gun switch is not activated. Do not touch these parts when the welding machine is on. Note: Before installing welding wire, be sure that the diameter of the welding wire matches the groove in the drive roller on the wire feed mechanism and that the wire size matches the contact tip

Electrodes used for shielded metal arc welding have two parts. The inner core is a metal rod or wire that should be similar in composition to the base metal. The outer coating is called flux. Various types of flux exist. Each coating is used for a particular welding situation. While the metal is molten, it can be contaminated by elements in the air. This contamination could weaken the weld. The flux coating creates a protective barrier called slag that protects the molten metal from contaminants

. The welder control panel contains information regarding proper input 3 Operating Instructions GTAW Arc Welding Torch voltage and amperage. Follow the specifications on the welder front panel. . The receptacle used for the welder must be properly grounded and the welder must be the only load on the power supply circuit. The Components of TIG Welding (not included with your WT6100 TIG torch) are: 1. A constant current power supply such as the Arcitech 110 inverter technology arc welder. 2. A bot

Remove the coating from the base metal. b. Make sure that the welding area is well ventilated. c. Use an air-supplied respirator. Extremely toxic fumes are created when these metals are heated. The electromagnetic field that is generated during arc welding may interfere with the operation of various electrical and electronic devices such as cardiac pacemakers. Persons using such devices should consult with their physician prior to performing any electric arc welding operations. ! WARNING . Never

Use una boquilla del tamano adecuado 2. Limpie o reemplace el forro interno de la pistola 3. Limpie o reemplace la punta de la pistola 4. Reemplacela 5. Apriete el tornillo de tension 36 Sp 1. Use un alambre seco y siempre debe almacenarlo un sitio seco 2. Reduzca la velocidad del alambre 3. Use solo alambre de fundente revestido alambres para soldadoras MIG, Models WF2050, WF2054, WF2057 & WF2058 Operation (Continued) 8. Switch the welder ON/OFF switch to the ON position. 9. Verify that the wir

Other positions require different techniques such as a weaving pass, circular pass, and jogging. A higher skill level is required to complete these welds. All work should be performed in the flat position if possible. For specific applications, consult an arc welding handbook. WELD PASSES Sometimes more then one pass is necessary to fill the joint. The root pass is first, followed by filler passes and the cover pass (See Figure 11). If the pieces are thick, it may be necessary to bevel the edges

These MIG items include but are not limited to; Contact Tips, Nozzles, Gun Liners, Drive Rollers, Felt Wire Cleaner. In addition, this warranty does not extend to any damage caused by the untimely replacement or maintenance of any of the previously listed CONSUMABLE parts. D. Any failure that results from accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with the product. E. Pre-delivery service, i.e. as

Welding operations may continue when the yellow lamp is no longer illuminated. POLARITY This welder is configured for DCEN, direct current electrode negative. helmet is recommended. Both hands are needed to stabilize and control the angle and arc length of the electrode. Operation 1. Be sure to read, understand, and comply with all precautions in the General Safety Information section. Be sure to read the entire section entitled Welding Guidelines prior to using this equipment. 2. Turn welder of

The polarity (+ or -) determines which direction the current is flowing. DC Reverse Polarity - occurs when the electrode holder is connected to the positive pole of the welding machine. Reverse Polarity directs more heat into melting the electrode rather than the work piece. It is used on thinner material. DC Straight Polarity - occurs when the electrode holder is connected to the negative pole of the welding machine. With straight polarity more heat is directed to the work piece for better pene

MANUAL 2. Turn welder off. 3. Verify surfaces of metals to be joined are free from dirt, rust, paint, oil, scale or other contaminants. These contaminants make welding difficult and cause poor welds. All persons operating this equipment or in the area while equipment is in use must wear protective welding gear including: eye protection with proper shade, flame resistant clothing, leather welding gloves and full foot protection. If heating, welding or cutting galvanized, zinc plated, lead, or cad