Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
1 Shielding Gas Cylinder For shielding gas connections, see welding power source Owner’s Manual. 2 Valve Open valve on cylinder just before welding. 3 Trigger Press trigger to energize welding power source contactor, start shielding gas flow, and begin wire feed. Wire feed speed is controlled by welding power source Wire Speed control (see appropriate welding power source Owner’s Manual). Close valve on cylinder when finished welding. 1 2 3 SECTION 5 . MAINTENANCE & TROUBLESHOOTING 5-1. Routine Maintenance Disconnect power before maintaining. Maintain more often during severe conditions. = Check = Change = Clean = Replace * To be done by Factory Authorized Service Agent Reference Every 3 y Unreadable Labels Weld Terminals Damaged Gas Hose Weld Cables Months Cords Gun Cables Every 6 Months OR Drive Rolls Inside Unit OM-1216 Page 14 5-2. Changing Drive Rolls 801 893-B Tools Needed: Turn Off power at welding power source first. 1 Drive Roll Cover Remove cover. Changing Push Roll: To remove push roll: 2 Push Roll Screw 3 Washer 4 Push Roll Remove screw and washer, and lift out drive roll. To install drive roll: Slide drive roll onto shaft and secure with washer and screw. Changing Lower Drive Roll: To remove drive roll: 5 Lower Drive Roll Screw 6 Washer 7 Lower Drive Roll 8 Drive Roll Key 9 Drive Roll Shaft Remove screw and washer, and lift out drive roll. Note: drive roll key will come out with drive roll. To install drive roll: Place drive roll key in slot in drive roll shaft. Line slot in drive roll up with drive roll key, and slide drive roll onto shaft. Secure drive roll with washer and screw. Reinstall gun case, if applicable. Reinstall drive roll cover. 1 2 3 4 5 6 7 8 9 It may be necessary to remove drive roll side of gun case to change lower drive roll. 5-3. Changing Liner Ref. 801 891-B Tools Needed: Turn Off power at welding power source first. 1 Nozzle 2 Contact Tip 3 Liner Remove and replace liner. Reinstall parts as shown. 1 2 3 5-4. Troubleshooting Trouble Remedy Gun tube assembly loose. Tighten nut at base of gun tube assembly. No weld output; gun/feeder does not work. Place Power switch on welding power source in the On position (see welding power source Owner’s Manual). Erratic weld output. Tighten and clean all connections. Pressing gun/feeder trigger does not energize welding power source; welding wire is not energized; shielding gas does not flow. Secure plug from gun/feeder trigger cord into 4-socket receptacle on welding power source (see Section 3-3, field kit instructions F207 643, or appropriate welding power source Owner’s Manual). Wire feeds, shielding gas flows, but welding wire is not energized. Secure control cable leads in welding power source (see field kit instructions F207 643 or appropriate welding power source Owner’s Manual). See Troubleshooting section in welding power source Owner’s Manual. Wire feeds erratically. Check and correct drive roll pressure (see Section 3-4). Clean or replace drive roll; clean or replace liner (see Sections 5-2 and 5-3). OM-1216 Page 15 Notes OM-1214 Page 16 SECTION 6 . ELECTRICAL DIAGRAMS 186 451 Figure 6-1. Circuit Diagram OM-1216 Page 17 OM-1216 Page 18 SECTION 7 . PARTS LIST Hardware is common and not available unless listed. 801 900-F 3 2 32 28 31 33 29 19 30 18 17 27 22 21 20 14 11 10 4 9 8 7 6 5 4 2 1 40 41 42 43 39 38 36 37 35 34 23 26 25 24 13 15 16 12 Figure 7-1. Complete Assembly For Spoolmate 3035 Item Dia. Part No. Mkgs. No. Description Quantity Figure 7-1. Complete Assembly for Spoolmate 3035 ... 1. . . PB1. . . . . 186 416. . TRIGGER SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 2 . . . . . . . . . . . . . 186 418 . . PLASTIC HANDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 3 . . . . . . . . . . . . . 196966 . . SPOOL COVER ASSY (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 4 . . . . . . . . . . . . . 194622 . . . . SPOOL DEFENCE SHELL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 5 . . . . . . . . . . . . . 194 623 . . . . SPOOL SHAFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 6 . . . . . . . . . . . . . 194 624 . . . . BUSHING RESISTANCE RUBBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 7 . . . . . . . . . . . . . 194 625 . . . . LOCATION BUSHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 8 . . . . . . . . . . . . . 194 626 . . . . ADJUSTING NUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 9 . . . . . . . . . . . . . . . . . . . . . . . . . . RING, rtng C-clip .140 shaft x .015 thick . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 10. . . . . . . . . . . . . 194 627 . . . . LOCKING SCREW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Эта инструкция также подходит к моделям:Сварочные аппараты - 3545 (819.55 kb)