Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
! Warning! To reduce the risk of fire and burn injury, use only spark plugs authorized by STIHL. Always press spark plug boot snugly onto spark plug terminal of the proper size. (Note: If terminal has detachable SAE adapter nut, it must be attached.) A loose connection between spark plug terminal and ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire. Keep spark plug clean, and make sure ignition lead is in good condition. ! Warning! Do not operate your cut-off machine if the muffler is damaged, missing or modified. An improperly maintained muffler will increase the risk of fire and hearing loss. Never touch a hot muffler or spill fuel or other flammable liquid over it. Burn injuries or fire will result. If your muffler was equipped with a spark- arresting screen to reduce the risk of fire (e. g. in the USA, Canada and Australia), never operate your cut-off machine if the screen is missing or damaged. For any maintenance please refer to the maintenance chart and to the warranty statement near the end of the instruction manual. Store wheels on a flat surface in a dry place, preferably at a constant temperature, where there is not a risk of frost. Do not store a cut-off machine with a wheel mounted on the machine. Store cut-off machine in a high or locked place, away from children. Empty the fuel tank before storing for longer than a few days. Store fuel only in correctly labeled and approved containers. Avoid direct skin contact and do not inhale the gas vapors. TS 400 17 English / USA Application Examples Most diamond cutting wheels are suitable for wet cutting Wet cut whenever feasible. It increases the service life and cutting speed of diamond cutting wheels Ensure that the cutting wheel is generously supplied with water, up to 10 liters per minute. Wet cutting helps to suppress dust. The water binds the dust. The cutting wheel must be supplied with at least 0.6 liters water per minute. Wet cutting can reduce the energy of reactive forces. In a pinch situation, the water can act as a lubricant. Water connection – A water attachment kit is mounted on the machine, for use with all types of water supply. – A pressurized 10 liter water tank is available from STIHL for dust suppression. – A water tank for mounting on the Cutquik cart is also available for dust suppression. Composite resin cutting wheelscan be used for dry cutting ofmetals or for wet or dry cutting of concrete, stone or masonry. Special procedures must be followed when dry cutting with a composite non- diamond wheel. See in the section entitled „Wet Cutting with Composite Wheels“ lin the safety precautions of this manual. Wet cutting is generally not suitable for cutting metals. Respiratory protection ! Warning! When wet cutting is not utilized, the operator and any bystanders should always wear a respirator approved by NIOSH/MSHA for the material being cut. Points to be noted with diamond and composite resin cuttingwheels Object to be cut – Must be fully supported – Must be secured so that it cannot roll or slip away – Must be protected against vibration The cutting sequence The cutting sequence is important when cutting openings and recesses, etc. The last cut must always be made in such a way that the cutting wheel cannot become bound and so that the user is not at risk of being injured by the part that has been cut off or out. If applicable, leave small ridges of uncut material to hold the severed part in position. These ridges can subsequently be broken through. A number of points must be decided before the part is finally severed: – How heavy is the part? – In which direction can it move after being severed? – Is it under tension? Helpers must not be put at risk of injury when the part is broken off or out. 18 TS 400 Cutting in several passes A = Mark cutting line : Work along the cutting line. If corrections are necessary, always reposition the cutting wheel, taking care to ensure that it is not wedged. The cutting depth per pass should not exceed 5 to 6 cm (2“ to 2 1/2“ . Thicker material must be cut in several passes. : Thick-walled workpieces should be cut with a uniform swinging movement, back and forth. English / USA Cutting slabs : Place the slab securely on a nonslip surface. A = Cut a guiding groove along the marked line. B = Cut deeper into the parting cut with uniform back-and-forth movements. C = Leave a ridge of uncut material. : Cut through the slab at the ends so the material does not chip. : Then break the slab. TS 400 19 English / USA Cutting round and hollow workpieces : Curves must be cut in several straight passes, taking care to ensure that the cutting wheel does : Pipes and round objects, etc. must not become wedged. be secured so that they cannot roll. : Avoid reinforcing elements, especially in the direction of the cut, when deciding on the cutting line. : Cut a guiding groove along the marked line. : Cut deeper into the parting cut with uniform back-and-forth...
Эта инструкция также подходит к моделям:Сварочные аппараты - TS 400 (3.12 mb)
Сварочные аппараты - TS 400 (3.12 mb)
Сварочные аппараты - TS 400 (3.12 mb)