Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
• If you are going to wall mount your dryer using the wall mounting kit included (see “Wall Mounting Instructions”). • Away from direct sunlight. Direct sunlight may affect the acrylic coating, plastic and electrical components. • Adequate ventilation • Room temperature that will not fall below 0. C. • Away from sources of heat such as coal or gas. Make sure that the dryer does not stand on its power cord. Ventilation openings must not be obstructed by carpeting when the dryer is installed on a carpeted floor. 7 • Wall Mounting Instructions Tools Required (Not Included) Tools and parts required for Plaster and or Wood Installation Drill & Drill Bit 1 Phillips Head Screw Driver 1 Expanding Wall Anchor 8 Wooden Slats 2 Wall Mounting Kit Includes the following: Description Wall Hanging Bracket 2 1” Phillips Head Screws 4 Plastic Spacers 2 .” Phillips Flat Head Screws 2 Exhaust Pipe 1 .” Phillips Round Head Screws 3 ** It is recommended to complete the following procedure with at least 2 people ** As wall materials vary, supplied hardware for fixing to the wall may be inappropriate for your wall type. Consult your local hardware / home improvement center for suggestions on the necessary hardware for your particular wall type. a) Determine the position where you will be installing the mounting bracket. • This dryer is not designed to sit on top of your washing machine. • A minimum of 2 inches is required between the top of the dryer and the ceiling above to allow easy installation and adequate spacing for exhaust. If mounting above a top load washing machine, allow sufficient spacing to open the lid of the washer or in the case of a front loading washer allow sufficient breathing space. b) Although the supplied mounting brackets can be installed directly to the wall using the existing wooden studs, the preferred method of installation is using wooden slats that provide a flat level installation surface and added stability to the whole wall installation. c) Use two wooden slats (not included) between the studs to mount the brackets. Required wooden slat size 23” Long x 3 .” High x 1” Deep When using the wooden slats to install on drywall material you must use expansion wall anchor bolts to safely secure the slats to the drywall. 8 d) Install the wall mounting brackets to the wooden slats installed in the previous step. Using the (4)1” Phillips Round head screws included, affix the mounting bracket to the wooden slats as shown in the diagram to the right. e) Install the exhaust pipe as shown in the illustration using the (3) .” long Phillips Flat head screws included. • For a downward exhaust join the sections (1) pointing downward. • For an upward exhaust join the sections (2) pointing upward 9 f) Install the lower wall spacers (included) using the (2 ) .” long Phillips Round head screws (included). These spaces are required when installing the unit on the wall to allow the necessary ventilation for efficient operation. Failure to install the spacers will both reduce the ventilation needed to operate your unit as well as put the appliance in tilted position on the wall which could present a possible unstable wall installation. g) Mounting the dryer to the wall hanging assembly. With the assistance of 2nd person lift the dryer and align the mounting holes at the rear of the dryer with the mounting brackets. Tilting the dryer to a 45. angle insert the hanging brackets into the mounting holes on the dryer as shown in the figure to the right. Once the dryer mounts are in place slowly lower the dryer in place and check all installation points for stress or weakened contact. 10 • Adjusting the leveling legs To install and adjust the leveling legs see the illustration to the right. If the floor is uneven adjust the legs (do not insert pieces of wood, or any other objects under the legs) • Adjust the height level of the legs accordingly. Place the dryer on a sturdy flat surface. If the dryer is placed on an uneven or weak surface, noise or vibration will occur. (Allowable is 1.) • Electrical Connection ..Warning• Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center. This appliance should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock. Do not under any circumstances cut or remove the third ground prong from the power cord supplied. Use of extension cord is not recommended. This appliance requires a standard 115/120-volt, 60Hz electrical outlet with three-prong ground. The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury. • CONTROL PANEL 11 • OPERATING INSTRUCTIONS • DRYING TIME REFERENCE ** LOAD WEIGHTS AND RESPECTIVE DRYING TIMES ARE APPROXIMATE ** Drying Capacity Drying Times High Heat Low ...