Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Release the "Anti-crease" and "DRYNESS" buttons. The "Child lock" indicator will flash and the dryer is now locked. 6. Turn off the dryer using the "On/Off" button. To deactivate the child lock Repeat steps 1. to 5. The "Child lock" indicator will go out. The control panel is now unlocked. 6. Turn off the dryer using the "On/Off" button. Dryer care Cleaning the lint filter ,A clogged filter is a fire hazard! The lint filter must be cleaned after every program. ^ Open the door and remove the lint filter by gently lifting it upwards. ^ Wipe the lint off the filter with your hand (do not use any sharp objects!) ^ Any lint remaining in the hollow part of the door can be removed through the gap at the bottom with a dust brush or vacuum. ^ Return the lint filter and close the door. The lint filter can be rinsed with hot water if necessary. The filter must be dried thoroughly before being returned to the dryer door. Dryer care Cleaning the exterior and the control panel ,To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the dryer. They will damage the surface. ^ The exterior and the control panel can be cleaned with warm water and liquid dish soap applied with a soft sponge. ^ Wipe dry. Cleaning the drum ^ The stainless steel surfaces of the drum can be cleaned using a non-abrasive stainless steel cleaner. ^ Wipe clean with a soft cloth. Dryer care Changing the light bulb ,To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Open the door. The bulb cover is located along the upper rim of the drum opening. ^Slide a screwdriver with a wide head underneath the side edge of the bulb cover and twist (see illustration). ^Flip down the bulb cover. ^ Replace the light bulb with a temperature proof bulb, available from Miele. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Flip up the light bulb cover and press it firmly until it clicks into place. ,Make sure the bulb cover is securely closed to prevent a short circuit or penetrating moisture. ^ Restore power. Frequently asked questions What if the dryer will not run? Possible fault Fix The "Start/Stop T" button was not pressed. Make sure the dryer is on. Press the "Start/ Stop T" button to begin the drying program. The circuit breaker tripped or the dryer is unplugged. Make sure the dryer is plugged in or reset the circuit breaker. The door is not closed. Close the door properly. How do I prevent static cling? Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer. What if the drum light does not come on? Possible fault Fix The bulb may be bad or burned out. See "Changing the light bulb." What if the "Child Lock" indicator flashes after turning the dryer on and a program cannot be started? Possible fault Fix The child lock is activated. Deactivate the child lock. See "Child Lock." What if the program stops, the "Anti-crease / End" indicator lights and the buzzer sounds? Possible fault Fix The drum is empty. Load laundry into the dryer. The dryer will not operate when the drum is empty. Single items should be dried with "Sturdy" or a timed program and dry items in the "Fluff" program. What if the "Filter/Vent" fault indicator is lit? Possible fault Fix The lint filter is clogged. Clean the lint filters. See "Dryer care". The exhaust hose or the connection is clogged with lint. Remove lint and check the exhaust system for blockages. The air supply in the room is insufficient. Open a window or door to increase airflow. Frequently asked questions What if the "Filter/Vent" indicator lights after cleaning the exhaust system? Possible fault Fix The dryer is not operating efficiently because the duct hose is too long. Check the exhaust length and diameter (see "How to calculate the effective duct length"). A long exhaust hose will increase program times and energy consumption. If the exhaust hose cannot be shortened, the indicator can be turned off by a service technician. What if the program runs too long or stops? Possible fault Fix The airflow is insufficient in the area of the dryer. Open a window or door to increase airflow. The lint filters are clogged. Clean the lint filters (see "Dryer care"). The laundry was not spun sufficiently in the washer. Select a higher spin speed in the wash program. The dryer is overloaded. Reduce the load size. Metal zippers interfere with the dryer’s moisture sensors. Select a timed program to avoid overdrying. An airflow gap of 3/8" (10 mm) must be provided between the machine and the floor. This gap must not be blocked by a toekick or thick piled carpets for sufficient airflow. What if the laundr...