Оценок - 4, средний балл: 4 ( )

Производитель: Nilfisk-ALTO Размер: 1.5 mb Название файла: Язык инструкции:

The squeegee assembly has a break away feature that is also used for mounting the squeegee. Loosen the knobs on the squeegee (figure 8). Slide the stud into the slotted hole in the support frame on the machine. 2. Attach the vacuum hose cuff to the squeegee hose fitting (see figure 9). 3. Tighten knobs. NOTE: Do not overtighten or break away feature is lost and damage may occur. NOTE: To prevent damage to the squeegee or machine, the squeegee was designed to break away from the machine. If the squeegee is impacted and it breaks away from the machine, simply reinstall it by following step 1-3. How to Adjust the Squeegee During operation, the rear squeegee blade should have a constant 3/16” minimum flare along the entire squeegee blade (see figure 10). 1. The squeegee body can be tilted to adjust the squeegee blade flare in the middle to match the flare on the ends. To adjust the tilt, loosen the adjusting bolt located on the left and right side of the squeegee (see figure 9). 2. Press down on the squeegee until both sets of guide wheels contact floor. 3. After making adjustments, retighten the screw(s). NOTE: It is important that the right and left wheels are contacting the floor in order for the squeegee to work. NOTE: As the rear squeegee blade wears, it can be rotated and/or flipped to obtain four good edges before having to change blades. A B Figure 7 Figure 8 Figure 9 3/16” minimum Figure 10 CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual Steering Page -13 r Operation How To Change or Rotate Brushes on Cylindrical Brush Head To install or rotate brushes on the cylindrical brush head: 1. Raise the brush deck and turn the key switch “OFF”. 2. Raise the brush skirt and pull out to remove. See figure 11. 3. Remove thumb screw from brush door. See figure 12. 4. Lower door approximately 12 mm and slide door and hub assembly from brush. See figure 13. 5. Slide brush off hub at opposite end. See figure 14. 6. Rotate brush or replace. 7. Slide brush on drive hub and insert door and hub assembly into brush core. 8. Raise door and install thumb screw. 9. Place side skirt on retainer pins and lower in place. 10. Brushes should be rotated after every 20 hours of use. Figure 11 Figure 12 Figure 13 Figure 14 Page -14- CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual Steering How To Prepare the Machine For Operation How To Prepare the Machine For Operation To install the brush or pad on the BOOST machine, follow this procedure: 1. Turn the key switch "ON". 2. Put the brush switch in the "UP" position. 3. Turn the key switch "OFF". 4. Go to the side of the machine. 5. Press on a brush or pad under the flex plates. See figure 15. NOTE: When using a black pad, position pad on head. Lower head and operate momentarily to affix pad to pad driver (if you have difficulty, position pad on floor and lower head then operate.) How To Remove The Brush Or Pad on the BOOST machine To remove the brush or pad from the machine, follow this procedure: 1. Turn the key switch "ON". 2. Put the brush switch in the "UP" position. 3. Turn the key switch "OFF". 4. Go to the side of the machine. 5. Pull downward on the brush or pad until it releases from the flex plates. See figure 16. Figure 15 Figure 16 CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual Steering Page -15 How To Operate The Machine How To Operate The Machine To restore the factory settings, follow the procedures below: 1. Press and hold the green one touch button (figure 17) until you hear a double beepfrom the machine. NOTE: The time required for this will be approximately 15 seconds. 2. The settings should be returned to 2 bars of solution and 1 bar of brush pressure. NOTE: The squeegee vac switch must be in the middle position for default settings to work. How to Move the Machine Without Power (see figure 18) 1. Engage manual override on brake (see page 9, “Parking Brake”). 2. Remove foot plate and 4 screws and locate steering motor. 3. Using the knob on steering motor, turn shaft on motor in direction you wish to turn machine. 4. Slowly push machine to desired location. NOTE: If you attempt to push machine too fast it will limit top speed. If this happens, stop and restart. 5. After moving machine, disengage manual brake override. NOTE: Machine will not function if override is engaged. Seat Adjustment (Standard) The standard seat is not adjustable forward or backward. Seat Adjustment (Deluxe) The optional deluxe seat is adjustable in three ways: 1. The seat can be adjusted to the forward/backward position by using the lever on the lower right side of the seat . Moving the...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: