Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Do not use TEFLON ®† tape. A combination of pipe fittings must be used to connect the dryer to the existing gas line. Shown is a recommended connection. Your connection may be different, according to the supply line type, size and location. A C D B A. .. ." flexible gas connector B. .. ." dryer pipe C. .. ." to ..." pipe elbow D. .. ." pipe-to- flare adapter fitting 3. Open the shutoff valve in the supply line. The valve is open when the handle is parallel to the gas pipe. A B A. Closed valve B. Open valve 4. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found. † ® TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company. Connect Vent 1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" ( 10.2 cm) clamp. 2. Move dryer into its final location. Do not crush or kink vent. 3. ( On gas models) Check that there are no kinks in the flexible gas line. 4. Once the exhaust vent connection is made, remove the corner posts and cardboard. Level Dryer Check the levelness of the dryer by first placing a level on the top of the dryer near the console. Then, by placing a level in the crease on the side of the dryer between the top of the dryer and the dryer cabinet, check the levelness from front to back. If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness. 12 Reverse Door Swing You can change your door swing from a right-side opening to a left-side opening, if desired. 1. Place a towel or soft cloth on top of the dryer or work space to protect the surface. Remove the door assembly 1. Open the dryer door. 2. Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front panel of the dryer. 3. Loosen the top screw from each of the 2 hinges in Step 2. A B A B A. Loosen these screws. B. Remove these screws. 4. Remove the dryer door and the hinges by lifting upward on the door. Lay the door on a flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose screws from dryer front panel. Reinstall the door 1. Remove the 4 screws and 2 hinges from the dryer door. 5. Remove the 4 plastic plugs located outside the dryer door opening. 6. Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in Step 4. Reverse the strike 1. Remove the door strike from the dryer door opening. 2. Remove the cosmetic screw opposite the door strike. A B A. Door strike B. Cosmetic screw 3. Reinstall the door strike and cosmetic screw on the opposite side of the dryer door opening from where they were removed. NOTE: Door strike and plugs must be on the same side of the dryer door opening. 13 2. Replace the 4 screws in the same holes. 5. Install screws in the top hinge holes in the door. Do not tighten screws. Leave approximately . " (5 mm) of screw exposed. A A 3. Remove the 4 screws from the opposite side of the door. 6. Hang door by placing screw heads into top slotted holes of hinges and slide door down. Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge screws. 4. Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge to the front panel. 7. Close door to engage door strike. A. Install these screws first. 14 Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/ recycle all packaging materials. 4. Check the dryer’s final location. Be sure the vent is not crushed or kinked. 5. Check that the dryer is level. See “ Level Dryer. ” WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 6. Plug into a grounded 3 prong outlet. Turn on power. 7. Remove any protective film or tape remaining on the dryer. NOTE: Glass door models have a protective film on the window that should be removed. 8. Read “Dryer Use. ” 9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. 10. Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this test, do not select the Air Fluff modifier. If the dryer will not start, check the following: ¦ Dryer is plugged into a grounded 3 prong outlet. ¦ Electrical supply is connected. ¦ Household fuse is intact and tight, or circuit breaker has not tripped. ¦ Dryer door is closed. 11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat...
Эта инструкция также подходит к моделям:Сушильные машины - Bravos W10150660A (1.03 mb)