Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
The Vent system chart provides venting requirements that will help to achieve the best drying performance. Vent system chart NOTE: Side and bottom exhaust installations have a 90. turn inside the dryer. To determine maximum exhaust length, add one 90. turn to the chart. Number of 90. turns or elbows Type of vent Box or Louvered hoods Angled hoods 0 Rigid metal Flexible metal 64 ft (20 m) 36 ft (11 m) 58 ft (17.7 m) 28 ft (8.5 m) 1 Rigid metal Flexible metal 54 ft (16.5 m) 31 ft (9.4 m) 48 ft (14.6 m) 23 ft (7 m) 2 Rigid metal Flexible metal 44 ft (13.4 m) 27 ft (8.2 m) 38 ft (11.6 m) 19 ft (5.8 m) 3 Rigid metal Flexible metal 35 ft (10.7 m) 25 ft (7.6 m) 29 ft (8.8 m) 17 ft (5.2 m) 4 Rigid metal Flexible metal 27 ft (8.2 m) 23 ft (7 m) 21 ft (6.4 m) 15 ft (4.6 m) Install Vent System 1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood. 2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp. 3. Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90. turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent. Install Leveling Legs WARNING Excessive Weight Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury. 1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer. 2. Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the cardboard. See illustration. 3. Examine the leveling legs. Find the diamond marking. 4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible. 5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent. Connect Vent 1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" (10.2 cm) clamp. 2. Move dryer into its final location. Do not crush or kink vent. 3. (On gas models) Check that there are no kinks in the flexible gas line. 4. Once the exhaust vent connection is made, remove the corner posts and cardboard. Level Dryer Check the levelness of the dryer. Check levelness first side to side, then front to back. If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness. Reverse Door Swing You can change your door swing from a right-side opening to a left-side opening, if desired. NOTE: For ease of installation, you may want to use 2 or more people to remove and reattach the dryer door. Remove the door 1. Place a towel or soft cloth on top of the dryer or work space to protect the surface. 2. Open the dryer door. Remove the 5 screws that hold the door hinge on the front panel of the dryer. A B C A. Dryer front panel B. Dryer door C. Screws 3. Remove the door. 4. Lay the dryer door on a flat, protected surface with the inside door assembly facing up. Remove the 5 screws to release the outer door assembly from the inner door assembly, as indicated below. See illustration. It is important that you remove only the 5 indicated screws. 5. Lift the inner door assembly off of the outer door assembly. Set the outer door assembly aside. Reverse the hinge 1. Place the inner door, screw head side up, on the work space. 2. Remove the 4 hinge screws that hold the hinge to the door and remove hinge. A A B B C C A. Hinge side screw B. Locator pins on hinge C. Top side screw 3. Move the large hole screw to the opposite side. Remove the 2 plug screws and plastic plugs, and insert them in the original screw holes on the opposite side. A CB A. Hinge screws B. Large hole screw C. Plug screws and plastic plugs 17 4. Move hinge to the other side and reattach with the 4 screws removed in Step 3. Make sure locator pins line up in holes and drive the top 2 screws in place first to help drive locator pins into proper location. 5. Set the inner door assembly aside. Reverse the door handle 1. Place the outer door assembly face down on work space. 2. Remove the 6 screws that hold the intermediate door to the outer door assembly. Remove the intermediate door, and set hinge shield aside. Remove the hinge hole cover. B C A A. Intermediate door B. Hinge shield C. Hinge hole cover 3. Rotate the window assembly 180. and reattach the intermediate door, hinge shield and hinge hole cover with the 6 screws removed in Step 2. Reinstalling the door 1. Place the inner do...
Эта инструкция также подходит к моделям:Сушильные машины - 110.8708 (1.72 mb)