Оценок - 3, средний балл: 4.3 ( )

Производитель: Speed Queen Размер: 703.49 kb Название файла: Язык инструкции:

FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P. CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P. 28 M412616 75 Pound (34 kg) Steam Non-reversing Tumblers CLEARANCES: Minimum to nearest Combustible Material Top — 12" (30.5 cm) Minimum. 0" permitted for first 4" (10.2 cm) along front of machine. Back — 0" - 24" (61 cm) Minimum recommended for service access. Sides — 0" Permitted. 3.81 cm (1-1/2") 71.75 cm (28-1/4") 97 cm (38-3/16") 134.6 cm (53") 194.6 cm (76-5/8") (4 Coil)203 cm (80") (6 Coil) DISCONNECT ELECTRICAL JUNCTION BOX 39.1 cm (15-1/4") 19 cm (7-1/2") 13.65 cm (5-3/8")200 cm (78-3/4") (6 Coil)184.8 cm (72-3/4") (4 Coil)164.5 cm (64-3/4") 98.1 cm (38-5/8") 34 cm(13-3/8") SWITCH 1.9 cm (3/4") I.D. STEAM INLET 1.9 cm (3/4") I.D. STEAM OUTLET 20.3 cm (8") DIAMETER EXHAUST DUCT THIMBLE CONNECTION T274IE3B M412616 29 75 (34 kg) Pound Steam Tumblers Cabinet Finish: Electrostatically applied thermosetting polyester Cylinder: 37" x 36" (94 x 91.4 cm) perforated galvanized steel with four baffles; 75 pounds (34.1 kg) dry weight (cotton load) Motor: (Non-reversing models) High Pressure Steam — 3/4 H.P. Low Pressure Steam — 3/4 H.P. Both motors are lifetime lubricated, internal overload protected. (See below for reversing models.) Boiler Horsepower: High Pressure Steam (6 Coil) — 4.60 BPH (154,100 BTU/hr., 72.1 kg/hr., 38,833 kCal/hr.) Low Pressure Steam (4 Coil) — 4.00 BHP (134,000 BTU/hr., 62.7 kg/hr., 33,768 kCal/hr.) Electrical Requirements: (See nameplate for voltage of your tumbler) Low Pressure — 230 Volt, 50 Hertz, 1 Phase, 8.5 Amp High Pressure — 230 Volt, 50 Hertz, 1 Phase, 9.0 Amp Air Flow: Low Pressure — 950 C.F.M. at 0.5" W.C. (449 liters/sec at 1.25 mBar) High Pressure — 900 C.F.M. at 0.5" W.C. (425 liters/sec at 1.25 mBar) Net Weight: 615 Pounds (280 kg) (approx.) REVERSING MOTOR SIZES GAS ELECTRIC STEAM HIGH PRESSURE LOW PRESSURE 75 LB. FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P. CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P. 30 M412616 SECTION II Installation Instructions RECEIVING INSPECTION Upon delivery, visually inspect crate carton and parts for any visible shipping damage. If crate, carton or cover are damaged or signs of possible damage are evident, have carrier note condition on shipping papers before shipping receipt is signed, or advise carrier of condition as soon as it is discovered. Remove crate and protective cover as soon as possible and check items listed on packing list. Advise carrier of any damaged or missing articles as soon as possible. A written claim should be filed with carrier immediately if articles are damaged or missing. IMPORTANT: Remove shipping tape from two back draft dampers located in exhaust thimble. MATERIALS REQUIRED (Obtain Locally) GAS, ELECTRIC OR STEAM DRYING TUMBLERS • •••••One circuit breaker. GAS DRYING TUMBLERS ONLY • •••••One gas shut-off valve for gas service line to each tumbler. STEAM DRYING TUMBLERS ONLY • •••••One steam shut-off gate valve for steam service line to be connected upstream of solenoid steam valve. FACILITIES REQUIRED FLOOR Drying tumbler may be installed on any level floor capable of supporting 100 pounds per square foot (488 kg/m2). Floor covering materials such as carpeting or tile should be removed. LAYOUT Whenever possible, tumbler should be installed along an outside wall where duct length can be kept to a minimum, and make-up air can be easily accessed. • •••••Two steam shut-off gate valves for each condensate return line. • •••••Flexible steam hoses with a 125 psig (pounds per square inch gauge) (8.79 kg/sq. cm) working pressure for connecting steam coils, Figures 24 and 25. • •••••Two steam traps for steam coil outlet to condensate return line. • •••••One steam pressure relief valve rated at 125 psig. (8.79 kg/cm2). Construction must not block airflow at top rear of tumbler. Doing so would prevent adequate air supply to tumbler’s combustion chamber. VENTING For maximum efficiency and minimum lint accumulation, tumbler air must be exhausted to outdoors by shortest possible route. M412616 31 Proper sized exhaust ducts are essential for pro...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: