Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Do not use an adaptor. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. WARNING! Electrical Shock Hazard Check with a qualified electrician or serviceperson if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug if it will not fit the outlet. Have the proper outlet installed by a qualified electrician. Failure to follow these instructions can result in death, fire, or electrical shock. Grounding for a cord-connected appliance This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. When this appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug, the plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances, or in their absence, with the National Electrical Code ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. Do not cut or remove the grounding prong from this plug. WARNING Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded. Refer to pages 21 – 27 for wiring details for electric dryers. WARNING! Electric Shock Hazard Use a new UL approved 30-ampere power cord or direct wire cable. Use a UL approved strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal. On all four wire installations remove the grounding link and connect the ground wire to the green ground connecting screw. Connect remaining 2 supply wires to remaining 2 terminals. Securely tighten all electrical connections. Failure to do so can result in death, fire, or electrical shock. 21Installation instructions Electrical requirements for electric models onlyNote: The wiring diagram is located in the control console. The dryer must be plugged into or connected to an individual branch circuit, do not use an extension cord. The power supply must be 220/240V or 208V, 60 Hz approved alternating current electrical service. The electrical service requirements can be found on the data label that is located on the splash back. A 30-ampere fuse or circuit breaker is required on each of the lines. If a power cord is used, the cord must be plugged into a 30-ampere receptacle. The power cord is NOT provided with U.S. electric model dryers. This dryer is supplied with the cabinet grounded through the neutral on the terminal block. If the dryer is to be installed in (1) a new branch circuit installation, (2) a mobile home, (3) a recreational vehicle, (4) an area where local codes do not permit grounding through the neutral conductor, the appliance grounding link must be removed and a 4-wire power cord/cable or a separate grounding wire must be used. Do not reuse a power supply cord/cable from an old dryer. The power cord/cable electric supply wiring must be retained at the dryer cabinet with a suitable UL listed strain relief. 208V requirements If your power supply is 208V 60 Hz, a new element kit must be fitted by a qualified electrician or service representative (see Accessories page 7 for kit part number). EN 22 Installation instructions Power supply cord requirements for U.S.A (for electric models only) Only a UL listed power-supply cord kit a suitable length for the installation and rated 120/240 V min, 30 A and marked with use for clothes dryers shall be used. This shall have ring terminals to connect to the dryer. The UL-rated strain relief included with it shall be suitable for a 1 1/8” (28.5 mm) hole. Fig.20 UL listed power-supply cord If your outlet looks like this Choose this power supply cord 3 wire 4 wire Connecting by direct wire Power supply cable must match power supply (4-wire or 3-wire) and be: Flexible armoured or non-metallic sheathed copper cable (with ground wire). All current- carrying wires must be insulated. 10 gauge AWG solid copper wire (do not use aluminium wire). Suitable length for the installation. A UL approved strain relief must be used. Grounding for a direct wired appliance This appliance must be connected to a grounded metal permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal on the appliance. Installation instructions 23 Electrical connections (electric models only) Please read Electrical requirements and grounding instructions on pages 20 – 21 first. Electric models of the dryer are manufactured for a 3-wire connection system. The dryer frame is grounded by a link to the neutral conductor on the dryer terminal block. If local codes do not permit grounding through the neutral, the grounding link from the terminal block must be ...
Эта инструкция также подходит к моделям:Сушильные машины - AeroSmart DE62T27C (1.54 mb)