Оценок - 2, средний балл: 4.5 ( )

Производитель: Conair Размер: 3.66 mb Название файла: Язык инструкции:

3 Bolt the dryer to the stand using the four 5/16”-18 bolts provided. Tools for installation: . 3/8” and 9/16” wrench . Hoist Mounting the Dryer and Hopper on a Mobile Floor Stand CAUTION: To prevent accident and injury, lift the empty hopper and the dryer onto the mobile floor stand using a hoist and the lifting lugs provided. Tools for installation: . 5/32” Allen wrench . 3/8” and 9/16” wrench . Phillips screwdriver . Flathead screwdriver . Hoist and strap 1 Lift the hopper onto the mobile floor stand using a hoist and the lifting lugs provided. Make sure you align the bolt holes in the mobile floor stand with the bolt holes on the discharge assembly. (continued) B-2 l Appendix Mounting the Dryer and Hopper on a Mobile Floor Stand (continued) 2 Bolt the hopper to the mobile floor stand. Using four 3/8”-16 (M 10) self-locking bolts, fasten the hopper to the mobile floor stand. 3 Lift the dryer onto the mobile floor stand using a hoist and lifting lugs provided. 4 Align the four bolt holes on the bottom of the dryer with the four bolts holes in the mobile floor stand stand. 5 Bolt the dryer to the mobile floor stand using the four 5/16”-18 self-locking bolts provided. Appendix l B-3 .TIP: Make the water supply and dis charge / return connections with flexible hoses at least 24 in. (61 cm) long. This allows you to easily remove the aftercooler assembly for cleaning. .TIP: If an optional flow control is also being installed with the aftercooler, the manual shut off valve should be installed on the inlet line for the flow control. Installing an Aftercooler (Optional) You can add an aftercooler to the D Carousel Dryer by ordering the optional after- cooler assembly. Installation is easy. The optional aftercooler requires a source of city, tower, or chiller water and a discharge or return line. You can use water at temperatures up to 85°F (30°C). But the water flow should be at least 1 gal/min (3.8 liters/min) for models D15, D25, D50; or 2 gal/min (7.6 liters/min) for models D75 and D100. 1 Stop the dryer and lockout the main power. 2 Remove the cover plate from the right side of the aftercooler housing on the dryer by removing the five screws. 3 Inspect the condition of the gasket. If the gasket is damaged, replace the gasket. 4 Insert the aftercooler assembly into the aftercooler housing. Make sure the staggered holes in the aftercooler mounting plate align with the holes in the aftercooler housing. C-1 l Appendix (continued) Installing an Aftercooler (Optional) (continued) 5 Secure the aftercooler assembly in the aftercooler housing using the five screws. . NOTE: If an optional flow control was ordered with the aftercooler, see Appendix E "Optional Flow Control"for information on connecting the water supply. 6 Connect the water supply line to the aftercooler inlet. If a manual shut off valve is used, it should be mounted on the inlet line. 7 Connect the water discharge or return line to the aftercooler outlet. 8 Install the plastic aftercooler cap over the water connections. Appendix l C-2 Cleaning the Aftercooler If you have the optional aftercooler, you need to clean the aftercooler coils to keep them working efficiently. Cleaning frequency depends on the type and amount of material you process. 1 Stop the dryer and lockout the main power. 2 Turn off the water flow to the water supply line. Disconnect supply and return lines. 3 Remove the plastic aftercooler cover. . NOTE: If an optional flow control was added with the aftercooler, remove the compression fitting from the aftercooler inlet. Loosen the fitting on the flow control, then swing the copper water supply tube out and away from the aftercooler inlet. 4 Remove the five screws securing the aftercooler in the aftercooler housing. .TIP: If the aftercooler (without a flow control) was installed using the recommended 24 in. (61 cm) of flexible hoses, there is no need to disconnect the hoses from the aftercooler inlet and outlet. (continued) C-3 l Appendix Cleaning the Aftercooler (continued) 5 Remove the aftercooler assembly from the aftercooler housing. 6 Clean the aftercooler assembly using a mild soap and water. Let the after- cooler dry thoroughly before installation. CAUTION: During the cleaning process, DO NOT cut or remove the stainless steel wire that holds the aftercooler assembly together. 7 Inspect the condition of the gasket. If it is damaged, replace the gasket. 8 Reassemble by repeating the steps in reverse order. (continued) Appendix l C-4 Cleaning the Aftercooler (continued) 9 Connect the water supply line to the aftercooler / precooler inlet. If a manual shut off valve is used, it should be mounted on the inlet line as well. 10 Connect the outlet of the aftercooler / precooler to the inlet of the flow control valve using the pre-shaped copper tubing and compression fittings provided. 11 Install the plastic aftercooler/precooler cover. 12 Turn on the flow control option through your control. C-5 l Appendix Installing the Flow Control (Opt...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: