Оценок - 3, средний балл: 3.7 ( )

Производитель: AEG Размер: 825.73 kb Название файла: 944726en.pdf Язык инструкции:

The machine may otherwise be damaged. • Before starting up for the first time, ensure that the nominal voltage and type of current specified on the machine type plate match the nominal voltage and type of current at the installation site. The electrical fuses required can also be found on the type plate. • Always connect the plug into a protection contact socket which has been installed as specified. • With permanent connections: A permanent connection may only be established by an authorised specialist electrician. • Do not install machine in rooms at risk of frost. • Ensure that the door of the machine cannot be blocked by interior doors of the house or the doors of other appliances. • Do not install on carpets with high piles. Air circulation will be hindered at the ventilation slots. • Ensure that the machine is not placed on its mains cable. • Install the machine horizontally. Transporting the appliance 1 Important: Only tip the appliance on its left side to transport (see illustration), if it cannot be transported in an upright position. Removing transport safety equipment 1 Caution! Before first starting up, all parts of the transport safety equipment must be removed. 1.Open loading door 2.Pull off adhesive strips from inside machine on top of drum. 3.Remove foil hose and polystyrene padding from the machine. 1 If the appliance was not transported in an upright position, leave it to stand for 12 hours before connecting it to the electricity supply and using it for the first time, so that the oil can flow back to the compressor. Otherwise the compressor could be damaged. Electrical connection Details on mains voltage, type of current and the fuses required should be taken from the type plate. The type plate is fitted near the loading aperture (see “Machine description” section). Important: The plug must be accessible after the appliance has been installed. Changing door stop 1 Warning! The door stop may only be changed by a specialist. If necessary, please contact our after-sales service or your specialist dealer. Warning! Before changing the door stop, disconnect the mains plug; with a permanent connection: fully unscrew or deactivate the fuse. 1.Open loading door. 2.Unscrew hinge A from the front of the machine and take off the loading door. 3.Remove cover plates B and C. To do this, insert a thin screwdriver into the slots as shown in the illustration, press downwards slightly and pry out the cover plates. 4.Use an appropriate tool and exert pressure to unfasten locking block D from the snap-on fixture, take out and reinsert on the other side, having rotated the block through 180°. 5.Unscrew hinge A from the loading door, rotate through 180°, reinsert on the opposite side and screw down. 6.Reinsert cover plates B and C on the opposite site having first rotated them through 180°. 7.Unscrew cover plates E from the front of the machine, rotate through 180, screw on the opposite side. 8.Unscrew door lock F, push down slightly and remove from the front of the machine. 9.Press snap-in button G in and down, press cover down slightly and remove from front of the machine. 10. Transfer door lock F to the opposite- side and screw down. 11. Fix cover G on to the other side and allow the snap-in button to lock in place. 12. Insert loading door and hinges into recesses on the front of the machine and screw down. Note regarding contact protection: The machine is only secure for operations again once all plastic parts have been inserted. Special accessories The following special accessories are available from your Service Force Centre or your specialist dealer: Intermediate installation kits for stacked washer and dryer: These intermediate installation kits can be used to arrange the dryer and an automatic AEG-Electrolux washing machine (60cm wide, front loading) as a space-saving washer/dryer stack. The automatic washing machine is at the bottom and the dryer is at the top. Version to be supplied: – with extractable stacker plate 916 019 103 Installation kit for external condensate drain Installation kit (125 122 510) for direct draining of condensate into a basin, siphon, gully, etc. The condensate tank then no longer has to be drained, it must however remain in its intended position in the machine. Refer to the “Programme options” section for how to deactivate the EMPTY WATER (RESERVOIR) display. Max. displacement height: 1m from the base of the dryer; max. displacement length: 3m Guarantee conditions Belgium DECLARATION OF GUARANTEE TERMS. Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer services department will repair this upon request, either during or after the guarantee period. The service life of the appliance will not, however, be reduced as a result. This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of the Civil Code. The statutory rights that the consumer has under this legislation are not affected ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: