Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
13A ASTA approved fuse to BS1362. Blue (Neutral) wire to terminal marked ‘N’ or Brown (Live) wire to coloured black. terminal marked ‘L’ or coloured red. Cord clamp ! If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock hazard. ! The power supply cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorised technicians (see Service). New or longer power cords are supplied at an extra charge by authorised dealers. ! The manufacturer denies any responsibility should any of these rules not be followed. ! If in doubt about any of the above consult a qualified electrician. Before you start using your dryer Once you have installed your dryer and before you use it, clean the inside of the drum to remove any dust that could have accumulated during transport. Installation GB Start and Warnings Maintenance Description Programmes Laundry Suggestions Care Troubleshooting Service 3 Dryer Description The front The back GB Control Panel Drum Air Intake Vent Caution: Hot! Vent Tube fitted here Rating plate Model & Serial numbers Filter Control panel Progress or Delay Lights Clean Filter Light On/Off Light ON/OFF Button PROGRAMMES Knob Indicator Options Programme Guide Buttons and Lights The START/CANCEL button starts a selected programme. When you press this button there will be one beep and the progress lights will flash to confirm the action. If you have not set a programme, the buzzer will beep four times. When a programme is running, holding this button cancels the programme and stops the dryer (see Start and Programmes). The OPTION buttons/lights select available options for your selected programme (see Start and Programmes). The lights indicate that the option has been selected. The Programme Guide allows you to consult a user friendly table of the available programmes. The Clean Filter light gives you a reminder before every programme that it is essential to clean the filter every time the dryer is used (see Maintenance and Care). START/CANCEL Button The On/Off indicator light signals that your dryer is in use or ready to select a programme. If this light flashes it indicates a fault (see Troubleshooting). The ON/OFF button : If the dryer is running and this button is pressed, the dryer stops. Press again, the dryer restarts. The Progress or Delay lights show you the status of the programme or the delay time when they flash. During a delayed start the lights flash to show the delay selected. When (not flashing) they show each stage of the programme by the corresponding light turning on (see Start and Programmes). The PROGRAMMES knob sets the programme: rotate it until the indicator is pointing to the programme you want to select (see Start and Programmes). 4 Start and Programmes Choosing a programme 1. Plug the dryer into the electrical socket. 2. Sort your laundry according to fabric type (see Laundry). 3. Open the door and make sure the filter is clean and in place (see Maintenance). 4. Load the machine and make sure items are not in the way of the door seal. Close the door. 5. If the On/Off light is not lit: Press the ON/OFF button . 6. Choose a programme by checking the Programmes Guide (see Programmes) as well as the indications for each type of fabric (see Laundry). - Select a programme by rotating the PROGRAMMES knob. 7. Set a delay time and other options if necessary. 8. If you wish to select the buzzer sound, at the end of the progamme, press the ALARM Option button. 9. Press the START button to begin. During the drying programme, you can check on your laundry and take out items that are dry while others continue drying. When you close the door again, press the START button in order to resume drying. 10. During the last few minutes of Drying Programmes, before the programme is completed, the final COOL TUMBLE phase is entered (fabrics are cooled), this phase should always be allowed to complete. 11. When the programme is complete. The buzzer will sound, if this option selected. Open the door, take the laundry out, clean the filter and replace it (see Maintenance). If you do not take out the laundry immediately, the dryer will tumble occasionally for 10 hours or until you open the door. 12. Unplug the dryer. GB Description Start and Programmes Warnings and Maintenance Laundry Suggestions Care Troubleshooting Service Installation Easy Iron Programme ‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle relaxes the fibres and makes them easier to iron and fold. ! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing. For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight:...