Оценок - , средний балл: ( )

Инструкция по эксплуатации Indesit, модель IDVA 735 S

Производитель: Indesit
Размер: 363.82 kb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

If it is necessary to fit a replacement fuse, it must be a 13 Amp ASTA approved to BS1362 type. WARNING: The plug must not be used without a fuse cover. If a replacement fuse holder/cover is required, it must be of the same colour coding or wording as shown on the base of the plug. Replacements are available from authorised dealers. Levelling the tumble dryer The tumble dryer should be installed level in order to operate correctly. After installing the tumble dryer in its permanent position, make sure it is level; check its side-to-side levelling first, followed by front-to-back. If the tumble dryer is not perfectly level, use a wooden block to support it while you adjust the two front feet, making them taller or shorter as necessary. Preliminary information Once the tumble dryer is installed, clean the inside of the drum before operating it and remove any dirt accumulated during transportation. Changing the plug The wires in the power cord are coloured in accordance with the following. Green and Yellow (Earth) wire to terminal marked “E”, symbol x, or coloured green and yellow. Blue (Neutral) wire to terminal marked ”N” or coloured black. 13A ASTA approved fuse to BS 1362. Brown (live) wire to teminal marked “L” or coloured red. ! If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO nOt leave it where it can be inserted into a socket and create a shock hazard. ! The power cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorized technicians (see Service). New or longer power cords are supplied at an extra charge by authorized dealers. ! The manufacturer denies any responsibility should any of these rules not be followed. ! If in doubt about any of the above consult a qualified electrician. 3 Description of the tumble dryer Front side Rear side Connection for ventilation hose Control panel On/Off button Options buttons and indicator lights Start/Pause button and indicator light 4 (î) inDesiT ON/OFF/Reset button Pressing the button normally will cause the machine to switch on or off. If the button is pressed for 3 seconds while the dryer is in function, the machine will switch off and the running cycle will reset. Programme selection knob Allows for setting the programme: turn until the indicator points towards the desired programme (see Starting and selecting a programme). Options buttons Allow for selecting the options available for the selected programme. The relative indicator lights turn on when the option has been selected (see Programmes and options). START/PAUSE button and indicator light When the green light flashes slowly, press the button to start the programme. When the cycle is under way, the indicator light remains on. To put the programme into pause mode, press the button again; the indicator light will turn orange and start flashing again. To resume the programme from the point it was interrupted, press the button again (see Start and programme selection). Indicator lights The indicator lights provide important information. They indicate the following: “Clean filter” indicator light Before each programme, the "Clean filter” indicator light signals that it is essential to clean the filter each time before using the tumble dryer (see Care and maintenance). “Drying phases” indicator lights The indicator light signals that the drying phase is running. The indicator light signals that the cooling phase is running. The END indicator light signals that the programme has ended. “Delay start” indicator light If the ”Delay start” option has been activated (see “Programmes and options”), after the programme has started, the indicator light corresponding to the chosen delay time will start flashing: o 3h O 6h //\x As time passes, the remaining delay will be displayed and the corresponding indicator light will flash: ~6^3h //\x O 6h O 9h Once the set delay time ends, the flashing LED will turn off and the set programme will start. 5 How to carry out a drying cycle Starting and selecting a programme 1. Plug the dryer into the power supply socket. 2. Select the programme according to the type of laundry (see Laundry). 3. Open the door, ensure that the filter is clean and securely placed. 4. Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door. 5. Press the ON/OFF button to start the machine. 6. After consulting the programme chart and the indications for each type of fabric (see Laundry), turn the Programme selection knob towards the programme corresponding to the type of laundry to be dried (see Programmes and options). ! Warning: If the position of the programme selection knob changes after pressing the START/PAUSE button, the selected programme will NOT be modified. To modify the programme, press the START/PAUSE button to put the programme in pause mode (the indicato...