Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
2 Open window venting 1. The end of the tube should be directed downwards, to prevent warm moist air from condensing in the room or in the dryer. ! Ensure that the dryer is adequately ventilated and that the end of the vent tube is not directed towards the air intake duct. ! The vent tube must always be fitted for optimum performance. ! Make sure that the vent tube and air intake vents are not obstructed or blocked. ! The dryer must not recycle exhaust air. ! Misusing a tumble dryer may create a fire hazard. ! Do not discharge exhaust air into a flue which is used for exhaust fumes from other appliances that burn gas or other fuels. Electrical connections Make sure of the following before you insert the plug into the the electrical socket: . The socket must be grounded. . The socket must be able to sustain the machines maximum power, which is indicated on the rating label (see Dryer Description). . Power voltage must be within the values indicated on the rating label (see Dryer Description). . The socket must be compatible with the dryers plug. Should this not be the case, replace the plug or the socket. ! The dryer must not be installed outdoors, even if the space is sheltered. It can be very dangerous if it is exposed to rain or storms. ! Once installed, the dryers electrical wire and plug must be within easy reach. ! Do not use extension cords. ! The power cord must not be bent or squashed. ! The power cord supplied is fitted with a BS1363 plug and a 13 amp BS1362 fuse. If you need to replace the fuse, use only those rated at 13 amp (13A) and ASTA approved to BS1362. Moulded plug ! The plug must not be used without the fuse cover in place. If a replacement fuse holder/cover is required, it must be of the same colour coding or wording as shown on the base of the plug. Replacements are available from authorised dealers. Changing the plug The wires in the power cord are coloured in accordance with the following: GREEN / YELLOW -EARTH BLUE -NEUTRAL BROWN -LIVE If a replacement plug is to be fitted, the appropriate wire must be connected to the correct terminal, as follows: Green and Yellow (Earth) wire to terminal marked ‘E’, symbol , or coloured green and yellow. 13A ASTA approved fuse to BS1362. Blue (Neutral) wire to terminal marked ‘N’ or Brown (Live) wire to coloured black. terminal marked ‘L’ or coloured red. Cord clamp ! If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock hazard. ! The power supply cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorised technicians (see Service). New or longer power cords are supplied at an extra charge by authorised dealers. ! The manufacturer denies any responsibility should any of these rules not be followed. ! If in doubt about any of the above consult a qualified electrician. Before you start using your dryer Once you have installed your dryer and before you use it, clean the inside of the drum to remove any dust that could have accumulated during transport. Installation GB Start and Warnings Maintenance Description Programmes Laundry Suggestions Care Troubleshooting Service 3 Dryer Description The front The back GB Air Intake Vent Drum Control Panel Rating plate Caution: Hot! Vent Tube fitted here Model & Serial numbers Filter Control panel START Indicator Button Drying Guide The START button begins drying a selected programme (see Start and Programmes). The HEAT button selects drying temperature (see Start and Programmes). IN: HIGH heat OUT: LOW heat The TIMER knob sets the drying time: rotate it clockwise, never counter-clockwise, until the indicator is pointing to the drying time you want (see Start and Programmes). HEAT TIMER Button Knob The Drying Guide allows you to consult a user friendly table of fabric types and load capacities. Cotton Synthetics or Acrylics and other delicates 4 Start and Programmes Choosing a programme 1. Plug the dryer into the electrical socket. 2. Sort your laundry according to fabric type (see Laundry). 3. Open the door and make sure the filter is clean and in place (see Maintenance). 4. Load the machine and make sure items are not in the way of the door seal. Close the door. 5. Choose the drying time by checking the Drying Guide table for the type of fabric you are drying (see Laundry). - Set the temperature with the HEAT button. - Select a drying time by rotating the TIMER knob clockwise. 6. Press the START button to begin. During the drying programme, you can check on your laundry and take out items that are dry while others continue drying. When you close the door again, press the START button in order to resume drying. 7. About 10 minutes before the programme is completed, it enters the final COOL TUMBLE phase (fabrics are cooled), which should always be allowed to complete. 8. Open the door, take the laundry out, clean the filter and rep...