Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Drum serial numbers Clean after each use Rating plate Air intake grille Vent hose fitted here Caution Hot NOTE: When the dryer is in use, avoid touching the back of the machine as it may be hot. Rear venting with hose Where to put and vent your dryer Ventilation Mobile Venting Fitting the Vent Hose Kit Your Tumble Dryer should NOT be located adjacent to a gas hob cooker, heater, or eye level grill as flames from the burners could cause damage to your machine. When the dryer is fitted under a work surface allow space for air to enter the rear grille, 10mm above the dryer minimum. If you are using this Dryer adjacent or stacked on top of a washing machine SEPARATE mains plugs and sockets must be used for each appliance. DO NOT use 2-way adaptors or extension leads. The Dryer dries your washing by drawing in air that is cool, clean and relatively dry, heating it and then blowing it through the clothes as they are gently tumbled. The moisture laden air is then blown out at the back of the dryer through the vent hose which is recommended for optimum performance. When operating the dryer, there has to be adequate ventilation to avoid the back flow of gases into the room from appliances burning other fuels, including open fires. A vent hose must always be fitted when the dryer is used in conjunction with Mobile Venting. The hose must be fitted securely into the back of the dryer (see diagram on previous page). If possible, it is always best to connect the hose to a permanent outlet close to the dryer (see instructions below). Ensure that the end of the hose is not directed towards the air intake grille at the rear of the dryer. If permanent installation is not possible, the dryer will work just as well with the hose passed through a partly-opened window. NOTE: The vent hose should not exceed 2.4 metres in length and should be kept free of any possible accumulation of fluff, lint (and water) by frequently shaking it out. Always ensure that the hose is not squashed. See diagram on previous page. Where to put and vent your dryer Permanent Venting Wall/Window Venting BA Storm cover In conjunction with the vent hose we recommend the use of a Wall/Window Vent Kit. These are available from your retailer or nearest Spares Centre. Fitting instructions are supplied with the kits, which can be mounted through a wall or window. Details of positioning for wall mounting are as follows:- Break a hole through the wall to the left of the proposed position for the dryer. Keep the hose as short and straight as possible to prevent condensed moisture running back into the dryer. Similarly the duct inserted into the wall should slope downwards to the outside. For window venting with stacked dryer, the hole in the window should ideally be made below the outlet and the hose should be kept as short as possible. Depending on the frequency of use, it is essential that the areas A and B in the illustrations are checked periodically and any fluff or debris removed. It is particularly important that the vent hose adaptor is fitted securely thus preventing any moisture laden air from being emitted back into the room. NOTE: The dryer should not be pushed so far back that the hose adaptor is pulled out of position or the hose squashed. The hose should be kept clear of the air intake grille and kinks or ‘U’ bends avoided as these will obstruct the hose or trap condensation. WARNING: 1. ENSURE THAT THE DRYER IS ADEQUATELY VENTILATED AND THAT THE END OF THE VENT HOSE IS NOT DIRECTED TOWARDS THE AIR INTAKE DUCT. 2. THE DRYER MUST NOT RECYCLE EXHAUST AIR. 3. THE VENT HOSE MUST ALWAYS BE FITTED FOR OPTIMUM PERFORMANCE. 4. MAKE SURE THAT THE VENT HOSE AND AIR INTAKE GRILLES ARE NOT OBSTRUCTED OR BLOCKED. 5. MISUSE OF A TUMBLE DRYER MAY CREATE A FIRE HAZARD. 6. DO NOT DISCHARGE THE EXHAUST AIR INTO A FLUE WHICH IS USED FOR EXHAUSTING FUMES FROM OTHER APPLIANCES BURNING GAS OR OTHER FUELS. For open window venting it must be possible for the end of the hose to be directed downwards to prevent warm, moist air condensing in the room or in the dryer. How to use your dryer 1. Plug in, switch on electricity. 2. Sort your laundry (see section “Sorting Your Laundry”) WARNING: WHEN SWITCHING electricity ON OR OFF, PLEASE ENSURE THAT YOUR HANDS ARE DRY. 3. Open the door. Check that the fluff filter is clean (see section “How to remove and clean the fluff filter”). 4. Load the dryer, placing the clothes carefully in the drum pushing them well towards the back and away from the door seal. Close the door. 5. Select the relevant heat setting (see section “The Button OUT LOW HEAT 6. Select the required programme/drying Controls”). time (See section Button IN HIGH HEAT “The Controls”). The dryer will start. 7. When finished, unlock and open the door and take out the laundry. Clean and replace the fluff filter. 8. Switch off electricity and remove plug from socket. WARNING: WHEN SWITCHING ELECTRICITY ON OR OFF, PLEASE ENSURE THAT YOUR HANDS ARE DRY. Door Release To open t...