Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
It has important safety and warranty information. It also hasmany suggestions for best drying results. To reduce the risk of fire, electric shock or injury to persons, read the IMPORTANTSAFETY INSTRUCTIONS in your dryer Owner’s Guide before operating this appliance. Operating Steps Read “Drying Procedures” in your Owner’s Guide. It explains these operating steps in detail. 1. Prepare items for drying. 2. Check that lint filter is clean and in place. 3. Load the dryer. If desired, add a dryer fabricsoftener sheet. Close the door. 4. Select the appropriate cycle and settings foreach load. • Turn the Cycle Selector knob to select thecycle.The estimated drying time will bedisplayed. • Suitable drying temperature, dryness level andoptions will automatically be indicated for eachcycle. To change the temperature and drynesslevel, press TEMP and DRYNESS until thedesired selections are made. • To select an option, press OPTIONS until theindicator for a desired option flashes and pressSelect. Follow the same steps to delete anoption. • If a dryness level or option is not available for acycle,it will not light. • Changes made to the cycle will automaticallybe remembered the next time that cycle isselected. • See the “Dryer Settings Chart” for more details. 5. Press START to begin the cycle. • To pause the cycle or change settings, pressPause/Cancel once. “ PAU” will be displayedalternately with the estimated drying time. To resume the cycle, press START. • To stop or change the cycle, press Pause/Cancel twice. 6. A signal will sound at the end of the cycle andperiodically during Press Saver when the CycleSignal option is selected. When the cycle ends,remove items immediately and hang or fold. 7. Clean the lint filter after every load. The Clean Lint Filter indicator will light at the end of thecycle as a reminder. Cycle Selection Turn the Cycle Selector knob to the desired cycle. For best results, follow the fabric care label instructions on items to be dried. To change the selection after the cycle has begun, press Pause/ Cancel twice, select a new cycle and press START. Just turning the knob to another selection will not change the cycle. The signal will beep and the status lights will flash, but the original cycle will continue. Auto Dry Auto Dry cycles take the guesswork out of drying time. Loads dried using the Towels, Normal, Perm Press and Delicate cycles will dry automatically at the selected temperature to the desired dryness level. The dryer uses sensing bars to sense the moisture level of the load as it tumbles through heated air. Auto Dry cycles save time and energyand protects fabrics. The estimated drying time will be displayed for 5 minutes. Then the outside of the display will light up in a circular track to indicate the drying time is automatically being determined by the sensors. When the load has reached the selected dryness level, it will continue to tumble, unheated, during a Cool Down period. This helps reduce wrinkling and makes items easier to handle during unloading. The estimated Cool Down time will be displayed. Drying time varies depending on size and dampness of load and fabric type. If the load is too small or almost dry, the sensing bars may not detect enough moisture to continue the cycle and the cycle may end after a few minutes. Select a Timed Dry setting to dry such loads. Room temperature and humidity, type of installation and electrical voltage or gas pressure can also affect drying time. Towels Select this Auto Dry cycle for towel loads. Normal Select this Auto Dry cycle for cotton items. Perm Press Select this Auto Dry cycle for cottons and blends with a no-iron finish. Delicate Select this Auto Dry cycle for knits and delicate items. PN 134431300D (0801) Cycle Selection Quick Select this cycle to up of just a few items. It provides approximately 20 minutes of tumbling down period. Bulky Select this cycle to dry a comforter, blanket, sleeping bag or similar item.Cool Down approximately 10 minutes. Timed Dry To manually select the drying time for any load, turn the knob to a numbered setting. Drying times from 15 to 90 minutes are available in 15-minute increments. You will not be able to select a cycle or dryness level. Timed Dry is recommended when using the No Heat option. Note: To change cycles, press Pause/Cancel twice. To avoid fire hazard, do not use heat to dry items containing feathers or down, foam rubber, plastic, or similarly textured, rubber-like materials. Use the No Heat setting only. Cycle Settings Appropriate drying temperature, dryness level and options will automatically be indicated for each cycle. The TEMP, DRYNESS and OPTIONS settings can be changed before the cycle is started. Those adjustments will automatically be remembered each time that cycle is selected. If a temperature, dryness level or option is not recommended for a cycle, the indicator will not light. If changes are attempted after the cycle starts, the status lights will blink, the signal will be...