Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
BThe ventilation hose should not be connected to the chimney of a stove or a fireplace. BDo not operate your product at the same time with heaters such as a coal or gas stove. Airflow may cause the chimney to flare up. Connection to water drain (Products with a condenser); In products equipped with condenser unit, water accumulated during the drying cycle accumulates in the water tank. You should drain accumulated water after each drying cycle. You can directly drain accumulated water through the water drain hose supplied with the product instead of periodically draining the water collected in the water tank. Connecting the water drain hose: 1. Pull the hose out by its end to remove it from the product. Do not use any tools to remove the hose. Attach the drain hose adaptor to the end of this hose. 2. Connect the special drain hose supplied with the product to the hose adaptor fitting. 3. Connect the other end of the drain hose directly to the wastewater drain or to the washbasin. The fitting must always be secured in every type of connection. Your house may flood if the hose comes out of its housing during water discharge. CWhen you direct the water drain to outside, “Water Tank” warning light will turn on at the end of each programme. Important: • The hose should be attached to a height of maximum 80 cm. • Make sure that the hose is not pinched or bend. • The end of the hose should not be bent, it should not be stepped on and it must not be folded between the drain and the product. Connecting the water drain hose for models with the water tank at the bottom; Connection pipe to water drain is at the bottom rear of your machine. 1. Remove the bracket and the rubber cap. 2. Attach the drain hose and replace the bracket to its position. Important: C There is no pump in the machine, so ensure that the hose is placed to allow a easy water flow. C The end of the hose should never be higher than the level of the water outlet on the machine. Otherwise, the “tank full” light of your machine will illuminate and stop the programme. C If the dryer is mounted on the washing machine by means of a bracket, use of the water drain hose is recommended. The drain hose should be directed downwards as shown in the figure. Adjusting feet In order to ensure that your product operates more silently and vibrationfree, it must stand level and balanced on its feet. Front feet of your product can be adjusted. Balance the machine by adjusting the feet. 1. Loosen the feet by hand. 2. Adjust the feet until the product stands level and firmly on the floor. CDo not use any tools to loosen the adjustable feet, otherwise, they can be damaged. CNever remove the adjustable feet from their housings. 2 plastic pieces supplied along with the user manual prevent your machine from slipping on wet and slippery surfaces. To install the plastic parts: 1. Tilt your product to backwards. 2. Fit the plastic parts on to the front adjustable feet. Press on the plastic parts to snap them into their seating. 3. Check the balance of your product again and readjust the adjustable feet if necessary. Electrical connection Connect the machine to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table. Our company shall not be liable for any damages that will arise when the machine is used on a circuit without grounding. • Connection must comply with national regulations. • If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse. • Power cable plug must be within easy reach after installation. • The voltage and allowed fuse or breaker protection are specified in the “Technical Specifications” section. • The specified voltage must be equal to your mains voltage. • Do not make connections via extension cables or multi-plugs. • The main fuse and switches must have a contact distance of minimum 3 mm. BDamaged power cable must only be replaced by a qualified electrician. BIf the product is faulty, it must not be operated unless it is repaired! There is the risk of electric shock! First use • To have the product ready for operation before calling the authorised service agent, make sure that its location and power supply installations are appropriate. If they are not, call a qualified electrician to have any necessary arrangements carried out. • Make sure that the power connections of the product are in accordance with the instructions given in relevant chapters of this manual. Disposing of packaging material Packaging materials are dangerous to children. Keep packaging materials in a safe place out of reach of children. Packaging materials of your product are manufactured from recyclable materials. Sort and dispose of them in accordance with recycled waste instructions. Do not dispose of them with normal domestic waste. Transportation of the machine 1. Unplug the machine from the mains. 2. Remove the water drain (if any) and chimney connections. 3...