Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine. -It will take longer to dry and as a result will use more electricity during drying. STEP 1. Open the door of your dryer. STEP 2. Pull out the filter (using the two finger grips). STEP 3. Clean any fluff deposits from the filter mesh. STEP 4. Refit the filter. - Make sure the arrows are facing you. STEP 5. Make sure the filter is pushed fully home. - NEVER run the dryer without the filter in position. ! You MUST clean fluff build up around the filter housing and the vent tube periodically, EVERY two or three months: -Check the vent tube and any permanent venting fixture to make sure that there has been no accumulation of fluff or lint, and remove it. -Remove lint that collects around the filter and the outlet vents. 2 Instruction booklet TUMBLE DRYER Contents Installation, 4-5 Where to put your dryer Ventilation Electrical connection Before you start using your dryer Dryer description, 6 The front The back Control panel Start and programmes, 7 Choosing a programme Laundry, 8-9 Sorting your laundry Wash care labels Special clothing items Drying times Warnings and Suggestions, 10 General safety Disposal Saving energy and respecting the environment Maintenance and Care, 11 Switching off the electricity Cleaning the filter after each cycle Check the drum after each cycle Cleaning the dryer Troubleshooting, 12 Service, 13 Spare parts GB ! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. ! Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works. 3 Installation GB Where to put your dryer . Place your dryer at a distance from gas ranges, stoves, heaters, or cook tops because flames can damage the appliance. Minimum gap 10mm . If you are going to install the appliance under a work counter, be sure to leave a 10mm space between the top and any other objects on or above the machine and a 15mm space between the sides and lateral furnishings or walls. This is to ensure proper air circulation. Make sure that the back vents are not obstructed. Minimum gaps 15mm . Make sure you put your dryer in an environment that is not damp and has proper air circulation throughout, the dryer will not operate efficiently in an enclosed space or cupboard. ! We do not recommend that the dryer is installed in a cupboard but the dryer must never be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the dryer door. Ventilation The Dryer dries your laundry by drawing in cool, clean and relatively dry air, heating it, and then distributing it through the clothes as they are gently tumbled. For optimum performance, the moist air is then blown out through a vent tube at the back of the dryer. When the dryer is in use, there has to be adequate ventilation to avoid the back flow of gases into the room from appliances burning other fuels, including open fires. Mobile venting A vent tube must always be fitted when the dryer is used in conjunction with Mobile Venting. The tube must be fitted securely into the back of the dryer (see Dryer Description). If possible, it is always best to connect the tube to a permanent outlet close to the dryer. If permanent installation is not possible, the dryer will work just as well with the tube passing through a partly-opened window. ! Ensure that the end of the tube is not directed toward the air intake vent at the rear of the dryer. ! The vent tube should not exceed 2.4 metres in length and should be kept free of any possible accumulation of fluff, lint and water by shaking it out frequently. Always ensure that the tube is not squashed. Permanent venting In conjunction with the vent tube we recommend using a Wall/Window Vent Kit, available at a retail location or the nearest Spare Parts Dealer. Wall mounting 1. Leave an opening in the wall to the left of the dryers proposed position. 2. Keep the tube as short and straight as possible to prevent condensed moisture from backing up into the dryer. 3. Similarly, the duct in the wall should slope downwards towards the outside. Window mounting 1. With a stacked dryer the hole in the window should ideally be made below the vent. 2. The tube should be kept as short as possible. Depending on how often you use your dryer, it is essential that areas A and B are checked periodically to remove lint or debris. The vent tube adaptor must be fitted securely thus preventing any humid air from being emitted back into the room. ! The Dryer should not be pushed so far back that the tube adaptor is pulled out of position or the tube is squashed or bent. ! The...