Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
To protect the heat pump from dirt, the dryer is fitted with a fluff filter, which is located in the filter housing. Here, too large amounts of fluff build up over time, which affect the function of the appliance. Important! • Operating when the fluff filter is clogged with fluff can damage the dryer. This also increases energy consumption. • Never operate the dryer without the fluff filters. 1. Open door in plinth: To do this, press the release button on the right and open the door in the plinth to the left. 18 2. Pull the filter housing out of the base by the handle. 3. Clean the inside of the door, the fluff filter chamber and the rubber seals of fluff. 4. Remove fluff from the fluff filter on the floor of the base with a damp hand. 5. To clean the fluff filter: Remove the filter from the filter housing. To do this, press the pressure points on the sides and pull the filter frame up and out of the housing. 1 1 2 6. Remove fluff from the fluff filter with a damp hand. If necessary, clean the filter under running water using a brush. 7. Insert the fluff filter into the filter housing. 8. As necessary, approx. once every 6 months, remove the fluff from the heat exchanger using the sponge supplied. When doing this, please use rubber gloves. 19 The fluff can be removed more easily if it is first dampened e. g. with a laundry dampener. It is best to use a vacuum cleaner for this purpose. Do not use any sharp objects in this area. 9. Re-insert filter housing along with filter in appliance base. If the fluff filter is not inserted in the filter housing, the filter housing cannot be slid into the appliance base. 10. Close door in plinth. Cleaning the drum Caution! Do not use abrasives or steel wool to clean the drum. Lime in the water or cleaning agents may form a barely visible lining on the inside of the drum. The degree to which the laundry has been dried is then no longer detected reliably. The laundry is damper than expected when removed from the dryer. Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down the inside of the drum and drum ribs. Clean operating screen and housing Caution! Do not use furniture cleaners or aggressive cleaning agents to clean the machine. Use a damp cloth to wipe down the operating screen and housing. 20 What to do if ... If, during operation, the error code E... plus the error is still displayed, please inform your number or letter) appears on the LCD: Switch local Service Force Centre and quote the the machine off and on again to reset the error code. programme. Press the Start/Pause button If Problem Possible cause Remedy Mains plug is not plugged in or fuse is not working correctly. Plug in at mains socket. Check fuse in fuse box (domestic installation). Dryer does not work. Loading door is open. Close loading door. Have you pressed the Start/ Press the Start/Pause button Pause button? again. Select a different programme the Wrong programme selected. next time you dry (see “Programme chart” chapter). Lint filters clogged. Clean lint filters. Fluff filter clogged. Clean fluff filter. Drying results unsatisfactory. Overloading of laundry. Observe recommended loading volumes. Ventilation slots in base area Uncover ventilation slots in base covered up. area. Clean inside surface of drum and drum ribs. Residue on inside surface of drum or drum ribs. Make an adjustment using the DRYNESS function (see chapter ”Daily use”) Loading door does not close. Fine strainer not in place and/or mesh filter not locked in place. Install fine strainer and/or snap large mesh filter into place. When a button is pressed, Err appears on the LCD. Washing protection. After the start of the programme, the option can no longer be set. Turn the programme knob to Off. Set the programme again. Programme selector in Off Turn programme selector to Drum light does not work. position. Defective light bulb. LIGHT or to any programme. Replace light bulb (see next section). 21 Programme time is corrected Displayed programme time automatically depending on type Automatic process; this is not a changes erratically or stays and volume of laundry and level machine fault. unchanged for a long time. of dampness. Programme inactive, empty water tank warning lamp Full tank lights. Drying cycle ends shortly after programme starts. END display illuminated. Drying cycle lasts an unusually long time. Note: After around 5 hours the drying cycle ends automatically (see „Drying cycle complete ”). The water reservoir is full. Not enough washing loaded or washing loaded is too dry for selected programme. Lint filter clogged. Fluff filter clogged. Load volume too big. Laundry insufficiently spun. Particularly high room temperature. Temporary switching off of the compressor to avoid overload. Empty the water reservoir, then start programme with Start/ Pause button. Select time programme or higher drying level (e.g. INTENSIVE DRY instead of STORAGE DRY). Clean lint filter. Clean fluff filter. Reduce load volume. L...