Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Es responsabilidad del propietario la instalacion correcta, incluso la del sistema de escape. LEAVE THESE INSTRUCTIONS WITH THE OWNER REMETTRE CES INSTRUCTIONS AU PROPRIETAIRE DEJE ESTAS INSTRUCCIONES CON EL PROPIETARIO DC68-02033C W10161760 1 Tools needed for installation • Teflon tape or pipe joint compound (gas only) • Cutting knife • Pipe wrench (gas only) • Nut drivers • Level • Screw driver (standard) • Duct tape • Crescent wrench ITEMS PROVIDED Electric Dryer Only Gas Dryer Only Proper installation is the responsibility of the owner. HOWEVER, SERVICE CALLS PERFORMED AS A RESULT OF POOR SET-UP, ADJUSTMENT AND CONNECTION ARE THE RESPONSIBILITY OF THE INSTALLER. Make sure you have everything necessary for proper installation. 1. GROUNDED ELECTRICAL OUTLET is required. See Electric Requirements. 2. POWER CORD for electric dryers (except Canada). 3. GAS LINES (if a gas dryer) must meet National and Local Codes. 4. EXHAUST SYSTEM – must be rigid metal or flexible stiff walled metal exhaust ducting. See Exhaust Requirements. CABINET DIMENSIONS 7200 series INCH (CM) A. Height-overall B. Width C. Depth-With Dryer Door Open 90° D. Depth E. Bottom Vent Hole Location - From Back To Center of Hole Side Vent Hole - From Back To Center Of Hole 38” (96.5) 27” (68.6) 46-7/16” (123.0) 28” (71.0) 7-1/2” (19) 8-1/2” (21.6) Note: The height of the dryer from top to floor is 38" with the leveling leg screwed all the way in. The customer can unscrew the leg out an additional 7\8" for a total overall height of 38 7/8". 2 IMPORTANT TO INSTALLER Please Read The Following Instructions Carefully Before Starting To Install The Dryer. These Instructions Should Be Retained For Future Reference. REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES SUCH AS DRYERS TO AVOID THE DANGER OF A CHILD SUFFOCATING. LOCATION CONSIDERATIONS The dryer should be located to permit adequate room in front for loading the dryer, and sufficient room behind the dryer for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the bottom or left side, use the accessory exhaust kit (see Accessories). Instructions are included with the kit. It is important to make sure the room has adequate make-up air. The area where the dryer is located must not obstruct the flow of combustion or ventilating air. On gas dryers, adequate clearance as noted on the data plate must be maintained to insure adequate air for combustion and proper operation of the dryer. THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO WATER AND/OR WEATHER. THE DRYER AREA IS TO BE KEPT CLEAR AND FREE FROM COMBUSTIBLE MATERIALS, GASOLINE AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER PRODUCES COMBUSTIBLE LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT FREE OF LINT. ALCOVE OR CLOSET INSTALLATION WARNING ! • An appliance installed in a closet shall have no other fuel- WARNING – burning appliance installed in the same closet. The dryer must be exhausted to • WARNING: To reduce the risk of fire, this the outside to dryer MUST BE EXHAUSTED TO THE reduce the risk OUTDOORS. See EXHAUST INFORMATION of fire when section. installed in an alcove or closet. • Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 2" front, 0" top, 0" either side and 2-3/8" rear. • Closet front must have two unobstructed air openings combined total area 72 in2 min., located 3 in min. from top and bottom. Louvered door with equivalent air opening is acceptable. MOBILE HOME INSTALLATION The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States,) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made. An anchor bracket kit is available with instructions (see Accessories). Locate in an area that has adequate make up air. A minimum of 72 in2 (183 cm2 ) of unobstructed opening is required. All mobile home installations must be exhausted to the outside with the exhaust duct termination securely fastened to the mobile home structure, using materials that will not support combustion. The exhaust duct may not terminate beneath the mobile home. See the section on exhausting for more information. 3 EXHAUSTING Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. In the United States: • All dryers must be exhausted to the outside. • Only rigid or flexible metal duct should be used for exhausting. In Canada: • All dryers must be exhausted to the outside. Outside the U.S. and Canada: • Refer to local codes. WARNING ! WARNING – plastic or nonmetal flexible duct presents a potential fire hazard. NEVER USE PLASTIC OR NONMETAL FLEXIBLE DUCT. If your existing ductwork is plastic, nonmetal or combustible, replace it wi...