.... .... .... .... .... .... .... ........ .... ........ ........ ........ .... .... .... .... .... .... .... .... ...................... M1102/M1103 Parts Diagram M1102/M1103 16-Speed Drill Press M1102/M1103 Parts List REF PART..# DESCRIPTION REF PART..# DESCRIPTION 1 XM1102001 HEAD..CASTING 2 XM1102002 SCALE..SLEEVE 3 XM1102003 PINION..SHAFT 4 XM1102004 FEED..HANDLE..M10-1.5..X..155 5 XM1102005 KNOB..M10-1.5 6 XPSS14M SET..SCREW..M8-1.25..X..12 7 XM1102007 KNOB..BOLT..M8-1.25..X..15 8 XM11020

The assembly should now be assembled as shown in Figure 8. Figure 6. Sliding table support and rack over the column. Figure 7. Correct column ring orientation. Figure 8. Handles and lock levers installed. SET UP -13 M1102/M1103 16-Speed Drill Press Headstock SET UP The headstock must be mounted on the column/base assembly before the drill press can be operated. Moving and installing the headstock is a two-person job. To install the headstock, do these steps: 1. Loosen the two set screws on the r

1. Damaged seal. 1. Replace damaged seals. Tool skips nails 1. Excessive air pressure. 1. Reduce air pressure to while discharging. 2. Air leaks. 3. Dirt in nose. 4. Dirt or damage prevents nails from moving freely. 5. Inadequate air flow to tool. 6. Worn piston O-ring or lack of lubrication. 7. Damaged trigger valve O- rings. 8. Worn bumper. 9. Cap seal leaking. tool. 2. Reseal and tighten screws and fittings. 3. Clean nose. 4. Clean magazine and inspect/repair damage. 5. Check fittings, hose,

1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking 1. Loose screws in housing. 1. Tighten screws. between housing 2. Damaged O-ring. 2. Replace O-ring and hose. 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between housing and cap. 1. Damaged seal. 1. Replace damaged seals. Tool skips staples 1. Excessive air pressure. 1.Reduce air pressure to tool. while discharging. 2. Air leaks. 3.

....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Clean inspect the parts for cracks, wear, or burrs. 9. Place a new O-ring on the new piston and apply a thin film of the nailer lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide at the bottom of the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston shaft with t

If you have comments about this manual, please contact us at: Woodstock International, Inc. Attn: Technical Documentation Manager P.O. Box 2309 Bellingham, WA 98227 Email: manuals@woodstockint.com Tool Data Staple Size .......................... 18 Gauge Staple Length........................ 5.8"-15.8" Staple Crown ...............................1.4" Magazine Capacity...............100 Staples Air Inlet.................................." NPT Weight ................................. 3.2 lbs. Oper

Figure 3. Loading nails into magazine. 4. Slide the nails all the way down to the nose of the nailer. 5. Release the magazine pusher by pulling back on the pusher and pressing in on the catch lever. Operating If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer, do these steps: 1. Connect

5. Nails are wrong angle. 1. Use correct nails. 2. Use undamaged, clean nails. 3. Tighten magazine. 4. Replace worn or damaged parts. 5. Use correct angle nails. Nailer does not fire. 1. Nailer is not lubricated. 2. Nail is jammed in magazine or discharge area. 3. Piston shaft is damaged. 4. Air pressure too low. 1. Follow lubricating instructions. 2. Clear nailer magazine or discharge area. 3. Replace piston shaft. 4. Check/increase air pressure. Air blows out of exhaust cap; nailer will not fi

Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as needed for satisfactory results. An in-line filter/lubricator/regulator unit, can be installed as depicted in Figure 1. This filter/lubricator/regulator unit will protect your tool from damaging water build-up, allow you to adjust and maintain regulated air pressure to your tool, and save you the inco