Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ Part No. 899223 (015) Fig. 3 Fig. 4 Fig. 3 Fig. 4 899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 2 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this tool NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the tool until you have written Porter- Cable and we have advised you. 1. USE SAFETY GLASSES. To prevent eye injuries, the tool operator and all persons in the work area must wear safety glasses with permanently attached, rigid, plastic side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87” printed or stamped on them). Fig. 1. 2. WEAR EAR PROTECTION to safeguard against possible hearing loss. Fig. 1. 3. OPERATOR AND BYSTANDERS WEAR HARD HAT to safeguard against possible injuries. Fig. 1. 4. USE CLEAN, DRY, REGULATED compressed air at 70 to 100 PSI, (4.8 to 6.9 BAR). Fig. 2. 5. DO NOT CONNECT TOOL TO pressure which potentially exceeds 200 PSI (13.8 BAR). 6. ONLY USE AIR HOSE THAT IS RATED for a maximum working pressure of at least 150 PSI or 150% of the maximum system pressure, which ever is greater. 7. NEVER USE OXYGEN, CARBON DIOXIDE, combustible gases or any other bottled gas as a power source for this tool: explosion and serious personal injury could result. Fig. 3. 8. CONNECT TOOL TO AIR SUPPLY HOSE with a coupling that removes all pressure from the tool when the coupling is disconnected. Fig. 4. 2 Technical Service Manager Porter-Cable Corporation 4825 Highway 45 North Jackson, TN 38305 Fig. 1 Fig. 2 Fig. 5 Fig. 6 Fig. 7 Fig. 9 1 2 Fig. 6 Fig. 7 Fig. 9 1 2 899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 3 9. DISCONNECT TOOL FROM AIR SUPPLY HOSE before doing tool maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, handing the tool to another person, or making adjustments. Fig. 5. 10. NEVER USE A TOOL that is leaking air, has missing or damaged parts, or requires repair. Make sure all screws and caps are securely tightened. 11. NEVER USE TOOL IF TRIGGER mechanism is inoperable, missing or damaged. Do not alter or remove trigger mechanism. Make daily inspections for free movement of trigger mechanism. 12. DO NOT USE TOOL WITHOUT SAFETY WARNING LABEL. If label is missing, damaged or unreadable, contact your Porter-Cable Service Center for a replacement. Fig. 6. 13. ONLY USE PARTS, FASTENERS, AND ACCESSORIES recommended by Porter-Cable. 14. REMOVE ALL FASTENERS from tool before connecting to air supply. The tool’s driving mechanism may cycle when tool is connected to the air supply. Fig. 7. 15. ALWAYS ASSUME THE TOOL CONTAINS FASTENERS. Keep the tool pointed away from yourself and others at all times. No horseplay. Respect the tool as a working implement. Fig. 8. 16. DO NOT LOAD FASTENERS with trigger depressed, to prevent unintentional firing of a fastener. Fig. 9. Fig. 8 3 899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 4 17. REMOVE FINGER FROM TRIGGER when not driving fasteners. Never carry tool with finger on trigger: tool will fire a fastener if rubber cap is bumped while trigger is depressed. Fig. 10. 18. USE THE MALLET TO RACK THE WOOD STRIP, NOT THE NAILER. Fig. 11. 19. DO NOT USE THE METAL END OF THE MALLET TO STRIKE THE PLUNGER, use the rubber capped end only. 20. FIRE FASTENERS INTO WORK SURFACE ONLY: never into materials too hard to penetrate. 21. DO NOT USE THE NAILER TO POSITION the flooring strips. Hitting the rubber cap without first activating the trigger will cause severe internal damage to the Nailer. Fig.12. 22. THE TRIGGER IS A SAFETY DEVICE and should only be pulled when the Nailer is in proper position on the work surface and before the rubber cap is struck with the mallet. Do not tie or tape down the safety trigger as the Nailer could discharge if dropped on the rubber cap. The Nailer will not fire unless the trigger is pulled before the mallet blow. Fig.13. 23. DO NOT DRIVE FASTENERS on top of other fasteners: the fasteners can ricochet causing personal injury. Fig. 10 Fig. 11 Fig. 12 Fig. 13 4 899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 5 EMPLOYER’S RESPONSIBILITIES WARNING: Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and follow all of these instructions carefully. OPERATIN...