Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
. Fig. 2. 3. Keep fingers AWAY from trigger when not driving fasteners to avoid accidental firing. 4. Choice of triggering method is important. Check manual for triggering options. See “Using the Tool with Selectable Triggering Options” section of this manual. 5. Never point tool at yourself or others in work area. Fig. 3 6. Never use oxygen or other bottled gasses. Explosion may occur. Never use combustible gases or any other reactive gas as a power source for this tool: explosion and serious personal injury could result. Fig. 3 & Fig. 4. 7. Wear ear protection to safe-guard against possible hearing loss. Ear protection equipment must conform to ANSI S3.19 requirements. Fig. 5. 8. Use clean, dry, regulated, compressed air at 70 to 120 PSI, (4.8 to 8.3 BAR). Fig. 6. Fig. 1 GENERAL SAFETY RULES 4 908991 - 12-12-02.qxd 12/12/02 11:18 AM Page 5 9. Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR). 10. Only use air hose that is rated for a maximum working pressure of at least 150 PSI (10.3 BAR) or 150% of the maximum system pressure, which ever is greater. 11. Connect tool to air supply hose with a coupling that automatically removes all pressure from the tool when the coupling is disconnected. Fig. 7. 12. Disconnect tool from air supply hose before doing tool maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person. Fig. 7. 13. Never use a tool that is leaking air, has missing or damaged parts, or requires repair. Make sure all screws and caps are securely tightened. Fig. 8. 14. Never use tool if safety, trigger or springs are inoperable, missing or damaged. Do not alter or remove safety, trigger, or springs. Make daily inspections for free movement of trigger and safety mechanism. Fig. 8. 15. Do not use tool without safety warning label. If label is missing, damaged or unreadable, contact your Porter-Cable Service Center for a replacement. Fig. 9. 16. Only use parts, fasteners and accessories approved by Porter-Cable. 17. Connect tool to air supply before loading fasteners, to prevent a fastener from being fired during connection. The tool driving mechanism may cycle when tool is connected to the air supply. Fig. 10. 18. Always assume the tool contains fasteners. No horseplay. Respect the tool as a working implement. Fig. 11. 19. Operator and bystanders wear hard hat to safeguard against possible injuries. Fig. 12. 20. Do not load fasteners with trigger or safety depressed, to prevent unintentional firing of a fastener. Fig. 13 Fig. 8 Fig. 9 Fig. 10 Fig. 7 Fig. 11 Fig. 13 Fig. 12 5 Fig. 16 Fig. 17 Fig. 16 Fig. 17 908991 - 12-12-02.qxd 12/12/02 11:18 AM Page 6 21. Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger. In “Contact Actuation Mode” tool will fire a fastener if safety is bumped while trigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footing and balance at all times when using or handling the tool. 23. Fire fasteners into work surface only: never into materials too hard to penetrate. Fig. 15. 24. Grip tool firmly to maintain control while allowing tool to recoil away from work surface as fastener is driven. In “Contact Actuation Mode” if safety element is allowed to recontact work surface before trigger is released an unwanted fastener will be fired. Fig. 14 Fig. 15 25. Do not drive fasteners on top of other fasteners, or with the tool at too steep an angle: the fasteners can ricochet causing personal injury. Fig. 15. 26. Do not drive fasteners close to the edge of the workpiece. The workpiece is likely to split allowing the fastener to fly free or ricochet causing personal injury. Fig. 16. 27. FOR CONTACT ACTUATION TOOLS ONLY, Do not use on scaffoldings or ladders or for tasks in which changing location involves the use of scaffoldings, stairs, ladders, and the like. Do not use for specific tasks such as closing boxes or crates or fitting transportation safety systems on vehicles and wagons. Fig. 17. TECHNICAL SPECIFICATIONS Noise level Typical Mean A - Weighted sound impulse . . . effective Acceleration . . . 3.91 m/s2 power level . . . . . . 95.1 dBA P - Emission sound pressure pressure level . . . . 86.3 dBA 6 7 Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY. Read and follow all of these instructions carefully. FOREWORD Porter-Cable Model Porter-Cable Model MS200 is a heavy duty pneumatic stapler. It is designed to install medium crown (7/16" wide), 16 ga. wire staples of various lengths (from 1" to 2" long). Use approved Porter-Cable fasteners only. POWER SOURCE This tool is designed to operate on clean, dry, compressed air at regulated pr...