Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
The nailer MUST OPERATE when in bump mode. The nailer MUST NOT OPERATE if in sequential mode. 8. Depress the Work Contact Element (WCE) against work surface. Pull the trigger. The nailer MUST OPERATE. LOADING THE NAILER 1. Always connect the tool to the air supply before loading fasteners. 2. Pull nail pusher mechanism back until pusher engages with magazine latch. 3. Load strips of fasteners into the magazine slot. Make sure that the nails are placed into tool at the proper orientation. 4. Squeeze the pusher and the latch together to unlatch pusher. Make sure the head of the last nail is under the head of the pusher. UNLOADING THE NAILER 1. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air hose before unloading. 2. Pull nail pusher mechanism back until pusher engages with magazine latch. 3. Hold tool upright so nails will slide backwards toward magazine slot. 4. Squeeze the pusher and latch together to unlatch the pusher once all nails have been removed. ADJUSTING THE NAIL PENETRATION The NS219001 and NS349001 nailers are equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface. 1. Adjust the operating pressure to a pressure which will consistently drive the fasteners. Do not exceed the maximum operating pressure of the nailer of 120 psi. 2. To adjust the depth-of-drive, loosen the 4mm bolt on the top of nose. To increase depth, push WCE in toward nose as much as desired. Re-tighten bolt. To decrease depth, pull WCE out as much as desired. Re-tighten bolt. 3. Make sure that the trigger and work contact element (WCE) move freely up and down without binding or sticking after each adjustment. ANTI-DRY FIRE These tools are equipped with an Anti-Dry Fire feature. This prevents the WCE from being pushed in when only a few nails remain. Simply load new nail clip behind remaining nails to continue shooting. ADJUSTING THE DIRECTION OF THE EXHAUST The nailers are equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. CLEARING A JAM FROM THE NAILER 1. Disconnect nailer from air supply. Model JB3495 5 Rotate Nail pusher mechanism Latch Nail pusher mechanism Latch 1 2 1 2 Operating Instructions 2. Remove all nails from the magazine (see Loading/ Unloading). Failure to do so will cause the nails to eject from the front of the tool. 3. Insert a screwdriver into the nose of the tool. Push up on the driver blade to free the jammed nail. 4. Grab the jammed nail with pliers and remove. Technical Support Please call our Nailer Hotline at 1-800543- 6400 with any questions regarding the operation or repair of this nailer or for additional copies of this manual. If calling from Ohio or outside of the continental United States, please call 1-513-367-1182. Fastener And Replacement Parts Use only genuine Campbell Hausfeld fasteners (or equivalent - see Fastener Interchange Information). Use only genuine Campbell Hausfeld replacement parts. Never substitute parts. Do not use modified parts or parts which will not give equivalent performance to the original equipment. Tool performance, safety and durability could be reduced. When ordering replacement parts or fasteners, specify by part number. Nailer Repair Nailer repairs must be performed by qualified and experienced service people ONLY. Assembly Procedure For Seals When repairing a nailer, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non- detergent oil, or equivalent, must be added through the air line before 6 Model JB3495 Fasteners JB3495 Tool will drive fasteners designed for: Porter Cable FC 350A, Hitachi NR83AA2, Senco FramePro 701XP, 751XP , Ridgid R350CHA, DeWalt D51822, D51823, and Paslode F-3505. Troubleshooting Guide Stop using nailer immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. Problem Cause Solution Air leaking at trigger valve O-Rings in trigger valve housing are damaged Replace O-Rings. Check operation of Work Contact Element (WCE) Air leaking between housing and nose Loose screws in housing Damaged O-Rings Tighten screws Replace O-Rings Damage to bumper Replace bumper Air leaking between housing and cap Loose screws Damaged gasket Tighten screws Replace gasket Nailer skips driving nail Worn bumper Replace bumper Dirt in nose piece Clean drive channel Dirt or damage prevent nails or pusher from moving freely in magazine Clean magazine Damaged pusher spring Replace spring Ina...