Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced. Service a. Tool service must be performed only by qualified repair personnel. b. When servicing a tool, use only identical replacement parts. Use only authorized parts. c. Use only the lubricants supplied with the tool or specified by the manufacturer. Do not make any modifications to the tool without first obtaining written approval from Campbell Hausfeld. Do not use the tool if any shields or guards are removed or altered. Do not use the tool as a hammer. Personal injury or tool damage may occur. Disconnect air supply and release tension from the pusher before attempting to clear jams because fasteners can be ejected from the front of the tool. Personal injury may occur. Air Source a. Never connect to an air source that is capable of exceeding 200 psi. Over pressurizing the tool is able to result in bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. b. Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool. Such gases are capable of explosion and serious injury to persons. Do not use any type of reactive gases, including, but not limited to, oxygen and combustible gases, as a power source. Use filtered, lubricated, regulated compressed air only. Use of a reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury. Use only a pressure-regulated compressed air source to limit the air pressure supplied to the tool. The regulated pressure must not exceed 120 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The tool could explode which will cause death or serious personal injury. Save These Inst ruct ions Do Not Disc ard Operating Inst ruct ions Lu brication This tool requires lubrication before using the tool for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis. The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void your warranty. 1. Disconnect the air supply from the tool to add lubricant. 2. Turn the tool so the air inlet is facing up. Place 4-5 drops of 30 W nondetergent oil into air inlet. Do not use detergent oils, oil additives, or air- tool oils. Air tool oils contain solvents which will damage the tool's internal components. 3. After adding oil, run tool briefly. Wipe off any excess oil from the cap exhaust. Rec ommended Hooku p The illustration below shows the recommended hookup for the tool. Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Regulator Lubricator Filter OIL O CO2 120 psi 5 NS219500 Operating Inst ruct ions (Continued) 1. The air compressor must be able to maintain a minimum of 70 psi when the 70 psi Min. 120 psi Max. tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. An oiler can be used to provide oil circulation through the tool. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool. 3. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 3/8 inch air hose for runs up to 50 feet. Use 1/2 inch air hoses for 50 foot run or longer. For better performance, install a 3/8 inch quick plug (1/4 inch NPT threads) with an inside diameter of .315 inch (8mm) on the tool and a 3/8 inch quick coupler on the air hose. 150 psi or greater 3/8 inch I.D. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the tool between 70 and 120 psi. No-Mar Deck ing Tip The no-mar decking tip is designed to eliminate marks caused by the serrated work contact element (WCE). The no-mar tip may be removed if not required (See REMOVING NO-MAR DECKING TIP). Use tool in single cycle mode (SEE OPERATIONAL MODES) when no-mar tip is in place. Rem oving No-Mar Deck ing Tip 1. Disconnect air supply from nailer. 2. Remove all fasteners from magazine (See UNLOADING THE NAILER). 3. Remove no-mar tip retaining ring. Retaining Ring No-Mar Tip 4. Pry no-mar tip away from the work contact element. Work Contact Element 5. Replace retaining ring onto no-mar tip, then store tip in safe place for future use. Inst alling No-Mar Deck ing Tip 1. Disconnect air supply ...