Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
3 General Safety Rules P.3, 4 List of Main Parts P.5 Tech. Specifications, Contents of Packing P.5 Operation P.6 Determining Proper Staple or Nail Length P.7 Maintenance P.7 Trouble Shooting P.8 Warranty Information P.9 Warranty Card P.11 IMPORTANT SAFEGUARDS 1. Staple Gun must not be loaded with staples and nails at the same time. 2. Do not lubricate. The Staple Gun has been lubricated at the factory. Under normal use it will not need further lubrication 3. Do not hold the Staple Gun toward people, it could invite serious injuries. 4. Store Staple Gun a dry locked cabinet and keep it out of reach of children. SAVE ALL INSTRUCTIONS GENERAL SAFETY RULES WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire or serious personal injury. The warnings, cautions, and instruction discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are a factor which cannot be built into this product, but must be supplied by the operator. WORK AREA 1. Keep your work area clean and well organized. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmosphere, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep bystanders, children and visitors away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY 1. Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This Plug will fit in a polarized outlet only one way. If the plug dose not fit fully in the outlet, reverse the plug. If it still dose not fit, contact a qualified electrician to install a polarized outlet. Do no change the plug in any way. 2. Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords may create a risk of fire. 3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. 4. Don’t expose Staple Gun to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 5. During normal operation, if anything happens, the power should be cut off at once and the tool should be checked and repaired PERSONAL SAFETY 1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. 2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing and gloves away from moving parts. It is recommended to wear protective goggles, gloves, sturdy non-slipping shoes and an apron while operating the machine. 3. Avoid accidental starting. Be sure switch is in LOCK position before connecting the unit to a power outlet. Carrying tools with your finger on the switch invites accidents. 4. Remove adjusting wrench before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. 5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 6. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. TOOL USE AND CARE 1. Use clamps or other practical way to secure and support the work piece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 3. Do not use tool if switch does not turn ON or OFF. Any tool that cannot be controlled with a switch is dangerous and must be repaired. 4. Disconnect battery pack from tool or place the switch in locked or OFF position before making any adjustments, changing accessories or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. 5. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. They should be kept away from work area. 6. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 7. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE 1. Tool service must be performed only by qualif...