Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
6. Do not exceed the maximum operating pressure of 95 PSI as stated in the Specifications Chart and warning label. 7. Ear protection is required for the operator and others in the work area. 8. Never attempt to drive staples on top of other staples. 9. Never attempt to keep the Trigger depressed with tape or wire. 10. Never leave the tool unattended or connected to the air supply when not in use. 11. Do not throw the tool or use it as a hammer to knock material into place. 12. Avoid prolonged use of the Stapler, and do not use this tool if you have back, neck or other bodily injuries that might be aggravated by the jerking motion of the tool. Stop using this tool if you experience pain in your arms or hands. 13. Do not use this tool if it is not loaded, as this will accelerate wear on the tool. 14. Be sure all hoses and fittings are free from damage and dirt. Replace any part that does not appear to be operating properly. Warning: People with pacemakers should consult with their physician(s) before using this product; operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure all parts listed on Page 7 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Maintenance 1. Do not store the Stapler in cold or freezing temperatures. If you are operating the Stapler in cold weather, use a permanent antifreeze as lubricant. Certain drying agents may damage o-rings and seals, so be sure to check these periodically. 2. It is recommended that you use an Oiler with this tool, especially if you use this tool regularly. Be sure the check the oil level in the Oiler before each use, and during prolonged periods of use. 3. If you are not using an Oiler, you must lubricate the Stapler before and after each use. Be sure to disconnect the tool from the air supply if you are lubricating it by hand. To lubricate this tool: add 5-6 drops of air tool lubrication to the Air Inlet. Do not use detergent oil or oil adhesives. Run the Stapler for a short time after lubrication and wipe off all excess oil. 4. A filter (not included) can be used to remove liquid and solid impurities which may rust or block internal parts and mechanisms. Periodically check the Filter and drain any water. Air Connection Note: Air Compressor is not supplied. You may use Quick-Couplers and Quick-Connectors (not supplied) as shown in the diagram above. Do not connect Couplers directly to the Air Inlet. Doing so will increase the overall bulk of the tool and strain the inlet threads. 1. Read and follow all safety precautions as listed on Pages 2-5 of this manual. 2. Acquire a Union Fitting (not supplied) and screw into the Air Plug [32, see Assembly Diagram on Page 8]. Tighten with a wrench. 3. Attach a Quick-Connector (not supplied) to the Union Fitting if desired. This allows quick exchange of the Air Hose to other air tools. 4. If staples do not drive down tightly, adjust to a higher pressure setting until satisfactory. Reduce air pressure if the staples are being driven too deep. This air tool requires lubrication during operation. For best results, it is recommended to have an Oiler and Water Filter in line with the Air Supply as shown. This will extend the life of the tool. Loading the Stapler When loading, the Stapler must be disconnected from the Air Compressor Hose. 1. Only use the proper size and type of staple with this tool, as specified in the chart on Page 2. 2. Disconnect tool from the air supply. 3. Depress the Click Lever [34] to release the spring-loaded Magazine Assembly [51] from the Upper Magazine [47]. Slide the Magazine Assembly out as far as it will go. See Figure A, right. 4. Turn the Stapler upside down. Place a full clip of staples inside the Upper Magazine so the pointed ends of the staples are directed away from the tool. STAPLER Figure A 5. Slide the Magazine Assembly back into place until it clicks. Operation 1. Grip the Body [18] of the Stapler with both hands and press the Nozzle [19] against the surface you wish to staple. Be sure to keep your hands, fingers and other body parts away from the Nozzle. 2. Depress the Trigger [28] to activate the Stapler. Your 1/2” Crown Air Stapler is easy to load and fun to use. With its comfortable grip and lightweight body, your Stapler is an ideal tool for working with upholstery, insulation, picture frames and more. Parts List DESCRIPTION Screw 5 x 22 Exhaust Cover Compression Spring Seal, Air Cylinder Cap O-Ring 11.8 x 2.4 Piston Set Washer 7.3 x 4.7 x 0.8 Head Valve Piston Piston Stopper O-Ring 26.6 x 2.4 O-...