Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
CAUTION: Do not store tools in a cold weather environment to prevent frost or ice formation on the tools operating valves and mechanisms that could cause tool failure. NOTE:Some commercial air line drying liquids are harmful to “O”-rings and seals – do not use these low temperature air dryers without checking compatibility. 5 LOADING THE N400S EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection. TO PREVENT ACCIDENTAL INJURIES: • Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected. • Never point the tool at anyone else. • Never engage in horseplay. • Never pull the trigger unless nose is directed at the work. • Always handle the tool with care. • Do not pull the trigger or depress the trip mechanism while loading the tool. 1. Open the magazine: 2. Load Nails: 3. Close Magazine: Pusher release tab. Pull pusher back to engage the latch. Hold nailer down with magazine tilted downward. Insert stick of nails Release pusher by first pulling back on the pusher and then pressing the pusher release tab. Slide pusher foreward against nails. NOTE: Use only nails recommended for use in BOSTITCH Framing nailers or nails which meet the BOSTITCH specifications. 6 FASTENER DEPTH CONTROL ADJUSTMENT When using the framing contact arm: The Fastener Depth Control Adjustment feature provides control of the nail drive depth from flush with or just above the work surface to shallow or deep countersink. TO ADJUST THE FASTENER DEPTH CONTROL: Disconnect tool from air supply before attempting any parts disassembly and before changing the work contacting element adjustment. 1. Rotate the fastener control adjustment to the right to increase depth of drive or to the left to decrease the depth of drive. DIRECTIONAL EXHAUST DEFLECTOR The adjustable exhaust deflector can be rotated into any desired position by hand without the use of any tools. Exhaust Deflector REMOVING NAILS 1. Pull pusher back until it engages latch. 2. Slide nails back to opening and remove nails. 7 TOOL OPERATION EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection. BEFORE HANDLING OR OPERATING THIS TOOL: I. READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL. II. REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL. There are two available operation modes on BOSTITCH pneumatic tools. They are: 1. SEQUENTIAL TRIP OPERATION 2. CONTACT TRIP OPERATION OPERATION BOSTITCH offers two types of triggers which can operate in one of two ways for pneumatic tools: Sequential Trip (gray trigger) and Contact Trip (black trigger). Each trigger has specific advantages. You should evaluate your particular construction project to determine which trigger is best. Your tool was shipped from the factory in the Sequential Trip (gray trigger) configuration. It can easily be converted to the Contact Trip (black trigger) mode of operation. 1. SEQUENTIAL TRIP OPERATION (GRAY TRIGGER): The Sequential Trip (gray trigger) gets its name from the “sequence” required to drive a fastener. To drive a fastener, the operator must first depress the “trip” FULLY against the work surface and then pull the trigger. To drive a second nail, the operator must lift the tool from the work surface, release the trigger and then repeat the above sequence. 1. The Sequential Trip (gray trigger): offers a positive safety advantage since it will not accidentally drive a fastener if the tool is bumped against any surface or anybody while the operator is holding the tools with the trigger pulled. 2. The Sequential Trip (gray trigger): allows “place nailing” without the possibility of driving a second, unwanted fastener on recoil as...
Эта инструкция также подходит к моделям:Строительные пистолеты - 171430REVA (954.49 kb)