Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
9 8 10 11 Clearing 22 Control Panel Messages for the Device The following table explains messages that might display on the printer’s Control Panel. Messages are listed in alphabetical order. Printer messages Message Description Recommended action CHECK STAPLER DEVICE alternates with CLEAR JAMMED STAPLE A staple jam occurred. Clear the staple jam. See page 19 for instructions. EXTERNAL DEVICE INITIALIZING The external device is initializing or recovering after clearing a jam condition. No action required. OUTPUT BIN FULL alternates with CLEAR PAPER FROM FACE UP The bin-full sensor in the left Face-up Bin has been reached. Empty the Face-up Bin. Control 23 Printer messages (continued) Message Description Recommended action OUTPUT BIN FULL alternates with CLEAR PAPER FROM OPTIONAL BIN 1 The Stacker Bin is full. Empty the Stacker Bin. STAPLER LOW ON STAPLES The Stapler Cartridge has 20 to 50 staples remaining. No action required. STAPLER OUT OF STAPLES There are no more staples in the Stapler Cartridge. Refill the Stapler Cartridge. See page 15 for instructions. STKR: ATTACH TO PRINTER The device is not attached to the printer properly. Make sure that there is a proper attachment between the device and the printer, and wait for a solid green status light on the user LED on the device. Control 24 Printer messages (continued) Message Description Recommended action STKR: CALL SERVICE A hardware malfunction occurred alternates with in the device. STKR: ERROR ZZ alternates with 66.XY.ZZ OUTPUT X is 1 or 2 and Y might be 2 or 3. DEVICE FAILURE Turn the printer off, and turn the printer on. If the condition persists, contact your HP-authorized service and support provider and report the error messages. See the user guide for your specific HP LaserJet printer for service and support information. STKR: CLOSE STAPLER DOOR The Stapler door is open or it is not closed properly. Close the Stapler door properly. STKR: DETACH AND CLEAR JAM A paper jam occurred in the device. Clear the paper jam. See page 17 for instructions. STKR: DETACH AND CLEAR STAPLE JAM A staple jam occurred. Open the Stapler door, and clear the paper or staple jam. See page 17 for instructions on clearing paper jams and page 19 for instructions on clearing staple jams. Control 25 Printer messages (continued) Message Description Recommended action STKR: TRAY OVERLOAD alternates with CLEAR PAPER FROM OPTIONAL BIN 1 The weight capacity of the stacker bin has been reached. Clear the paper from the Stacker Bin. TOO MANY PAGES IN JOB TO STAPLE The job height is greater than the stapler capacity. The height of the job to be stapled should not exceed 5 mm. See the stapling specifications on page 32 for more information. Control 26 Determining System Problems Output does not go to selected bin Situation Possible Reason Job went to a different The selected bin does not support the media used. (See bin than was expected. page 30 for supported paper sizes.) Note Envelopes, labels, and transparencies are ONLY supported Face-up Bin. The Stapler can staple jobs of 2 to 50 sheets or job is thicker than this, the job is ejected unstapled. hold a maximum of 3,000 sheets, depending Determining 27 Problems with the device Situation Possible Reason Job was not stapled. . The job height exceeds the stapling capacity (5 mm) . (HP 3000-sheet Stapler/ . There is a staple jam. Stacker only) . A single-page job was sent to the Stapler; it will not be stapled. . The Stapler ran out of staples. Printer does not recognize the device or the user LED on the device is off. . Check the power cords (see page 29). . Check the C-link cables (see page 29). . Make sure that the device has been configured in printer driver. . If the printer still does not recognize the device, a dealer or authorized HP service provider. guide for your specific HP LaserJet printer for service and support information. Device does not . Make sure that the power cord power on. the device and the power box 29). Remove and reconnect the power cord. . Turn the printer off, check page 29), and turn the printer Determining 28 Problems with the device (continued) Situation Possible Reason Paper jams and paper feeding problems. . Make sure that you are using the supported paper weights and sizes (see page 30). . Check the cables and connectors between the printer and the device. See page 29 for cabling configurations. . Repeated paper jams between the printer and the device might mean that the printer and device are set up on an uneven floor. Level the device. See the installation guide for instructions. CAUTION Using paper outside HP specifications may cause requiring repair. This repair is not covered by the or service agreements. See the paper specifications your specific HP LaserJet printer. Determining 29 Determining System Problems Cabling Installation Roadmap 3 0 Supported Paper Sizes Tray, Bin, or Capacity Paper Weight Stapler Face-up Bin Up to 125 sheets Letter (20 lb bond) A4 (80 g/m2) . Letter, ISO A4 (lands...
Эта инструкция также подходит к моделям:Строительные пистолеты - C4779x (351.08 kb)