Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
An inadequate air supply can cause a loss of power and inconsistent driving. 2. An oiler can be used to provide oil circulation through the tool. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool. 3. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 1/4 inch air hose for runs up to 50 feet. Use 3/8 inch or greater air hoses for 50 foot run or longer. For better performance, install a 3/8 inch quick plug (1/4 inch NPT threads) with an inside diameter of .315 inch (8mm) on the tool and a 3/8 inch quick coupler on the air hose. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the tool between 60 and 100 psi. OIL O CO2 100 psi 150 psi or greater 60 psi Min. 100 psi Max. Recommended Hookup Quick Plug Air Hose Quick Plug (Optional) Regulator Filter Quick Coupler Lubricator Quick Coupler (Optional) 5 CHN10202, CHN10210 Operating Instructions (Continued) Operational Mode Always know the operational mode of the tool before using. Failure to know the operational mode could result in death or serious personal injury. Single Sequential Mode This tool requires the trigger to be pulled each time a fastener is driven. The tool can be actuated by depressing the Work Contact Element (WCE) against the work surface followed by pulling the trigger. The trigger must be released to reset the tool before another fastener can be driven. Operating a Sequential Trip Tool Check the operation of the Work Contact Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the tool if the WCE trip mechanism is not operating properly. Personal injury may occur. 1. Disconnect the air supply from the tool. 2. Remove all nails from the magazine (see Loading/ Unloading). 3. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. 4. Reconnect air supply to the tool. 5. Depress the WCE against the work surface without pulling the trigger. The tool must not operate . Do not use the tool if it operates without pulling the trigger. Personal injury may result. 6. Remove the tool from the work surface. The WCE must return to its original down position. The tool must not operate . Do not use the tool if it operates while lifted from the work surface. Personal injury may result. 7. Pull the trigger and depress the WCE against the work surface. The tool MUST NOT operate . 8. Depress the WCE against the work surface. Pull the trigger. The tool MUST operate . An improperly functioning tool must not be used. Do not actuate the tool unless the tool is placed firmly against the work piece. Loading / Unloading The Tool 1. Always disconnect the tool from the air supply before loading fasteners. 2. Push down on the latch button. Pull back on the magazine cover. 3. Insert a stick of Campbell Hausfeld nails or equivalent (see "Fasteners" section) into the magazine. Make sure the pointed ends of the nails are resting on the bottom ledge of the magazine when loading. Make sure the nails are not dirty or damaged. 4. Push the magazine cover forward until the latch catches. 5. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air hose before unloading. Adjusting the Nail Penetration The tool is equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface. 1. Adjust operating pressure so nails are driven consistently. Do not exceed 100 psi. 2. To drive the nail shallower, turn the wheel (C) to right to the extent desired. 3. To sink a nail deeper, turn the wheel (C) to left to the extent desired. 4. Make sure trigger and work contact element move freely up and down without binding or sticking after each adjustment. Adjusting The Direction Of The Exhaust The tool is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. 1 2 1 2 Rotate 1 2 (C) 6 Operating Instructions User - Maintenance Instructions Clearing A Jam From The Tool 1. Disconnect the air supply from the tool. 2. Remove all nails from the magazine (see Loading/ Unloading). Failure to remove all fasteners will cause the fasteners to eject from the front of the tool. 3. Undo latch by pulling out and down. The wire latch will disengage from the hooks on the nose. 4. The door can now be rotated, exposing the jammed fastener. 5. Remove the jammed fastener, using pliers or a scre...
Эта инструкция также подходит к моделям:Строительные пистолеты - CHN10210 (13.02 mb)