Оценок - 4, средний балл: 3.3 ( )

Производитель: Campbell Hausfeld Размер: 1.56 mb Название файла: Язык инструкции:

A separate ‘red’ trigger for “Bottom Trip” mode is included with tool as an accessory. SINGLE CYCLE MODE When the black trigger is installed, nailer is in single cycle mode. This method is recommended when precise nail placement is required. Operation in this mode requires trigger to be pulled each time a nail is driven. Nailer can be actuated by depressing the Work Contact Element (WCE) against work surface followed by pulling the trigger. The trigger must be released after each fastener is driven to allow tool to reset. Since the tool can only be actuated by first removing the finger from the trigger, this is considered to be a more restrictive mode of operation, suitable for less experienced users. BOTTOM TRIP MODE When the red trigger is installed, the nailer is in bottom trip mode. This method is recommended when less precise nail placement is required. Operation in this mode requires trigger to be depressed with nailer off of the work surface. Then, the nose of the nailer is tapped against the work surface causing a nail to be driven. Each time the Work Contact Element is depressed, a nail is driven into the work surface. Extreme care should be taken because a nail will be driven when the WCE is pressed against any surface. Since the tool can be actuated without removing the finger from the trigger, this is considered to be a less restrictive mode, suitable for more experienced users. MODE CONVERSION To convert the tool from one mode to the other: 1. Remove o-ring on the side of trigger pin. 2. Remove trigger pin, trigger, and trigger spring. 3. Switch out only the trigger. 4. Replace trigger spring, trigger, trigger pin, and o-ring. Do not attempt to modify the trigger components in any manner and do not attempt to use any other trigger components other than those intended for this tool. Contact your Campbell Hausfeld representative if you have any questions. Mode Conversion Trigger spring O-ring Trigger pin Trigger WORK CONTACT ELEMENT (WCE) Check the operation of the Work Contact Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the nailer if the WCE trip mechanism is not operating properly. Personal injury may occur. 1. Disconnect the air supply from the nailer. 2. Remove all nails from the magazine (see Unloading The Nailer). 3. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. 4. Reconnect air supply to the nailer. 5. Depress the Work Contact Element (WCE) against the work surface without pulling the trigger. The nailer MUST NOT OPERATE. Do not use the tool if it operates without pulling the trigger. Personal injury may result. 4 Models NS219001, NS219500, NS319001 & NS349001 6. Remove nailer from work surface. The Work Contact Element (WCE) must return to its original down position. Pull the trigger. The nailer MUST NOT OPERATE. Do not use the tool if it operates while lifted from the work surface. Personal injury may result. 7. Pull the trigger and depress the work contact element (WCE) against the work surface. The nailer MUST OPERATE. 1 2 8.Depress the Work Contact Element (WCE) against work surface. Pull the trigger. The nailer MUST OPERATE. 1 2 LOADING THE NAILER 1.Always connect the tool to the air supply before loading fasteners. 2.Pull nail Nail pusher mechanism Latch pusher mechanism back until pusher engages with magazine latch. 3. Load strips of fasteners into the magazine slot. Make sure that the nails are placed into tool at the proper orientation. 4. Squeeze the pusher and the latch together to unlatch pusher. Make sure the head of the last nail is under the head of the pusher. UNLOADING THE NAILER 1. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air hose before unloading. 2. Pull nail pusher mechanism back until pusher engages with magazine latch. Nail pusher mechanism Latch 3. Hold tool upright so nails will slide backwards toward magazine slot. 4. Squeeze the pusher and latch together to unlatch the pusher once all nails have been removed. ADJUSTING THE NAIL PENETRATION The NS219001, NS319001 and NS349001 nailers are equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface. 1. Adjust the operating pressure to a pressure which will consistently drive the fasteners. Do not exceed the maximum operating pressure of the nailer of 120 psi. 2. To adjust the depth-of-drive, loosen the 4mm bolt on the top of nose. To increase depth, push WCE in toward nose as much as desired. Re-tighten bolt. To decrease depth, pull WCE out as much as desired. Re-tighten bolt. 3. Make sure that the trigger and work contact element (WCE) move freely up and down without binding or sticking after...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: