Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
b) by line oiler A line oiler is installed on the tool’s air inlet, which provides the necessary oil for lubrication. c) manual lubrication If neither a service unit nor a line oiler exists in the pressurised air system, 3 -5 drops of pneumatic oil must be given into the air inlet before each use. . Store air tools in dry rooms only. 10 5.2 Trouble shooting Trouble shooting Faults and possible causes Remedy A. Air escapes between lid and housing: O-rings damages or soiled Clean or replace O-rings, tighten screws fully B. Fasteners are not driven all the way in: Working pressure too low. Cross section of air hose too small. Tool without lubrication ncrease air pressure in 0.5 bar increments, until fasteners are properly driven. Min. 6 mm inner diameter required. Clean parts and lubricate. C. Fasteners are driven too far into the material Working pressure too high. Reduce working pressure in steps of 0.5 bar. D. Fasteners project or are bend: Tool not held down firmly enough. Hold down tool more firmly or increase working pressure, if necessary. 11 6. Specifications KG 80/16 Air consumption (per shot) 0.34 l Working pressure 4.5 - 7.0 bar Magazine capacity (staples/brads) 160 pcs. Dimensions (LxWxH) 238x45x151 mm Weight (w/o fasteners) 0.78 kg A-weighted single-shot emission sound power level (LPA 1S) 83 dB A-weighted single-shot emission sound power level (LPA 1S) 76 dB Vibration 1,73 m/sec2 Recommend inner air hose diameter 6 mm Suitable fasteners staples type 80 4 - 16 mm Crown width of staples 12,8 mm Wire size 0,95 x 0,65 mm Pressurised air required: clean and free of condensate, with fine mist of oil Compressor capacity: min. 50 l/min filling capacity Recommended working pressure Max. working pressure set at regulator or filter/pressure regulator 7 bar. 7. Standard Delivery Air Stapler KG 80/16 2 Allen keys 1 Safety glasses 1 Can pneumatic oil 1 Blow moulded case 1 Instruction manual 8. Accessories Staples Type 80/06 CNK, crown 12.8 mm, 6 mm long (3000 pcs.) Stock-no. 090 105 3855 Type 80/08 CNK, crown 12.8 mm, 8 mm long (3000 pcs.) Stock-no. 090 105 3863 Type 80/10 CNK, crown 12.8 mm, 10 mm long (3000 pcs.) Stock-no. 090 105 3871 Type 80/12 CNK, crown 12.8 mm, 12 mm long (3000 pcs.) Stock-no. 090 105 3880 Type 80/14 CNK, crown 12.8 mm, 14 mm long (3000 pcs.) Stock-no. 090 105 3898 Type 80/16 CNK, crown 12.8 mm, 16 mm long (3000 pcs.) Stock-no. 090 105 3901 12 1. Vue d’ensemble de l’agrafeuse KG 80/16 F 2 3 1 5 4 Pos. Designation 1. Securite de declenchement 2. Raccord pour air comprime 3. Detente 4. Levier de blocage 5. Poussoir de magasin 13 Sommaire 1. Vue d’ensemble de l’agrafeuse KG 80/16 2. A lire en premier ! 2.1 Utilisation conforme aux prescriptions 3. Consignes de securite 3.1 Directives 3.2 Securite de l’appareil 3.3 Securite de service 4. Mise en service 5. Maintenance et entretien 5.1 Conseils d’entretien 5.2 Derangements / Reparation 6. Caracteristiques techniques 7. Etendue de la livraison 8. Accessoires 2. A lire en premier ! . Lire les presentes instructions d...
Эта инструкция также подходит к моделям:Строительные пистолеты - KG 16 (1.6 mb)