Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
j Pull the magazine slider 7 completely out of the magazine 5 . j If necessary remove any staples or nails of the wrong type from the magazine 5 . j Slide the correct staples or nails into the magazine 5 . j Look at the depiction on the magazine slider 7 for how to insert the staples or nails correctly. j Push the magazine slider 7 into the magazine 5 until it meets the stop. j Then press the magazine slider 7 downwards until it has definitely engaged. Q Switching ON and OFF m CAUTION! Connect the tool to the mains only when it is switched off. To do this set the on/ oFF switch 8 to position “0”. To switch ON: j Set the on/oFF switch 8 to position “I” (see Fig. A). GB/IE/CY To switch OFF: j Set the on/oFF switch 8 to position “0”. m Blow count: The Electric Tacker PET 23 VARIo is designed for 30 blows per minute. m Continuous Operating Time: The Electric Tacker PET 23 VARIo is designed for 15 minutes of continuous operation at the maximum blow count. Allow the appliance to cool down sufficiently after such a tasking. Q Setting the impact force A tip! j Select the lowest impact force required for stapling. j You can set the impact force at any value between “1” (lowest impact force) and “7” (highest im- pact force) using the impact force controller Q Stapling j j j j 2 . Switch on the tool. Press the nose 4 on the spot where you wish to staple. Press the trigger Adjust the impact force to suit the materials, staples or nails. 6 . Redriving: Note: Use this function if you discover that some already-driven staples or nails have not ended up Commissioning / Rectifying faults flush in the material. Redriving must be carried out directly at each staple or nail. If you do not lift the nose 4 when doing this then no further staple or nail will be loaded into the driving position. j Drive the required staple or nail and press the nose piece 4 once more on to the next redriving position. j Press the trigger 2 as often as necessary until the staple or nail is flush with the substrate. Examples of use: j Fastening a covering to the seat of a chair (see Fig. B). j Fixing a skirting at the joint between the wall and floor covering (see Fig. C). j Stretching and stapling a canvas to a frame (see Fig. D). j Attaching a protective film to insulation material when installing thermal insulation (see Fig. E). j Attaching fixings for components in a wall cladding system (see Fig. F). Q Rectifying faults WARNING! Before you clean or maintain the device always pull the mains plug out of the mains socket. =Fault =Cause =Remedy The tool does not work properly. A staple or nail is blocking the tool. open the magazine slider 7 . This should release the pretension. Take off the front plate 3 with the hexagonal socket screw key 10. Remove the staple or nail. A staple or nail has been incorrectly driven into the material. Remove the incorrectly driven staple or nail with pincers or pointed pliers. Select suitable staples or nails. Set the required impact force that will correctly drive the staples or nails. GB/IE/CY Maintenance and cleaning / Disposal / Information Q Maintenance and cleaning CAUTION! Always pull the plug out of the mains socket before cleaning or maintaining the device. The electric tacker is designed to be maintenance-free. j j j Always keep the device clean, dry and free of oil or grease. Clean the device frequently. This should be done immediately after you have finished using it. Do not allow any liquids to enter the device. Use a cloth to clean the housing. never use petrol, solvents or cleaning agents that might attack plastic. Q Disposal The packaging is wholly composed of environmentally-friendly materials that can be disposed of at a local recycling centre. Do not dispose of electrical power tools with the household rubbish! In accordance with European Directive 2002/96/EC (covering waste electrical and electronic equipment) and its transposition into national legislation, worn out electrical power tools must be collected separately and taken for environmentally compatible recycling. Contact your local refuse disposal authority for more details of how to dispose of your worn out electrical devices. Q Information Q Service centre The service centre for your country is shown in the warranty documentation. WARNING! Have your device repaired only by qualified specialist personnel using original manufacturer parts only. This will ensure that your device remains safe to use. WARNING! If the plug or mains lead needs to be replaced, always have the replacement carried out by the manufacturer or its service centre. This will ensure that your device remains safe to use. Note: Through poor conditions of the electrical mains, shortly voltage drops can appear when starting the equipment. This can influence other equipment (eg. Blinking of a lamp). If the mains- impedance zmax<0.381oHM, such disturbances are not expected. (In case of need, you may contact you local supply authority for further information.) GB/IE/CY Informat...