Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Failure to do so may result in serious injury to tool operator or persons in the vicinity. 4 FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION CAUTION: • Always lock the trigger and disconnect the hose before adjusting or checking function on the tool. 007006 1 A B 1. Adjuster To adjust the depth of nailing, turn the adjuster. The depth of nailing is the deepest when the adjuster is turned fully in the A direction shown in the figure. It will become shallower as the adjuster is turned in the B direction. If nails cannot be driven deep enough even when the adjuster is turned fully in the A direction, increase the air pressure. If nails are driven too deep even when the adjuster is turned fully in the B direction, decrease the air pressure. Generally speaking, the tool service life will be longer when the tool is used with lower air pressure and the adjuster set to a lower depth of nail driving. Hook 007062 1. Hook 1 CAUTION: • Always lock the trigger and disconnect the hose from the tool. • Never hook the tool at high location or on potentially unstable surface. The hook is convenient for hanging the tool temporarily. To use the hook, simply lift up hook until it snaps into the open position. When not in use, always lower hook until it snaps into the closed position. ASSEMBLY CAUTION: • Always lock the trigger and disconnect the hose before carrying out any work on the tool. Loading nailer 007007 Select nails suitable for your work. Insert strip of nails into the magazine. Pull the pusher lever to the rear to engage the pusher to the last nail. 007008 1 1. Pusher Unloading nailer 007009 3 1 2 1. Pusher lever 2. Depress 3. Return Pull the pusher lever to the rear. Return the pusher lever back while keeping the pusher depressed to disengage it from the strip of nails. Depress the nail stopper and remove the strip of nails from the magazine. 5 007010 007010 Nail stopper 1 Connecting air hose 007011 1 2 1. Air socket 2. Air fitting Lock the trigger. Slip the air socket of the air hose onto the air fitting on the nailer. Be sure that the air socket locks firmly into position when installed onto the air fitting. A hose coupling must be installed on or near the tool in such a way that the pressure reservoir will discharge at the time the air supply coupling is disconnected. OPERATION CAUTION: • Make sure all safety systems are in working order before operation. 1. To drive a nail, you may place the contact element against the workpiece and pull the trigger, or 007012 1 007013 2. Pull the trigger first and then place the contact element against the workpiece. • No. 1 method is for intermittent nailing, when you wish to drive a nail carefully and very accurately. No. 2 method is for continuous nailing. CAUTION: • However when the tool is set to the “Intermittent Nailing” mode, WITH THE TRIGGER HELD IN A HALF-PULLED POSITION, an unexpected nailing could occur, if contact element is allowed to re-contact against the workpiece or the other surface under the influence of recoil. In order to avoid this unexpected nailing, perform as follows; A. Do not place the contact element against the work- piece with excessive force. B. Pull the trigger fully and hold it on for 1-2 seconds after nailing. • For No. 1 method, set the change lever to the position. For No. 2 method, set the change lever to the position. After using the change lever to change the nailing method, always make sure that the change lever is properly set to the position for the desired nailing method. 007014 1. Continuous nailing 2. Trigger lock 3. Lock lever 4. Intermittent nailing Anti dry fire mechanism This tool is equipped with an anti dry fire mechanism. When there are a few nails remaining in the magazine, the contact arm will be locked in the undepressed position to prevent the tool from being activated. Load more nails to resume operation. Jammed nailer 004308 1 2 3 4 1. Hammer 2. Small rod 3. Ejection port 4. Driver 1 2 3 4 2 6 7 CAUTION: • Always lock the trigger, disconnect the hose and remove the nails from the magazine before cleaning a jam. When the nailer becomes jammed, do as follows: Insert a small rod or the like into the ejection port and tap it with a hammer to retract the driver. Use pliers to bend the jammed nail so that the nail head comes out of the slot in the driver guide. Then remove the jammed nail. Nails Handle nail coils and their box carefully. If the nail coils have been handled roughly, they may be out of shape or their connector breaks, causing poor nail feed. Avoid storing nails in a very humid or hot place or place exposed to direct sunlight. MAINTENANCE CAUTION: • Always disconnect the air hose from the tool before attempting to perform inspection or maintenance. Maintenance of nailer Always check the tool for its overall condition and loose screws before operation. Tighten as required. With tool disconnected, make daily inspection to assure free movement of the contact element and trigger. Do not use tool if the contact eleme...
Эта инструкция также подходит к моделям:Строительные пистолеты - AN923 (877.18 kb)