Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
You can perform nailing operations with less fatigue by doing so. A nail will be bent or the tool can become jammed if you mistakenly nail on top of another nail or strike a knot in the wood. The nail may be thrown and hit someone, or the tool itself can react dangerously. Place the nails with care. I Do not leave the loaded tool or the air compressor under pressure for a long time out in the sun. Be sure that dust, sand, chips and foreign matter will not enter the tool in the place where you leave it setting. c *Do not point the ejection port at anyone in the vicinity. Keep hands and feet away from the ejection port area. 7 *When the air hose is connected, do not carry the tool with your finger on the trigger or hand it to someone in this condition. Accidental firing can be extremely dangerous. Handle the tool carefully a s there is high pressure inside the tool that can be dangerous if a crack is caused by rough handling (dropping or striking). Do not attempt to carve or engrave on the tool. Stop nailing operations immediately if you notice something wrong or out of the ordinary with the tool. Always lock the trigger, disconnect the air hose and remove all of the nails before inspection, maintenance, relocating, or after operation is over. 8 z" Perform cleaning and maintenance right after finishing the job. Keep the tool in tip-top condition. Lubricate moving parts to prevent rusting and minimize friction related wear. Wipe off all dust from the parts. When not operating the tool, always lock the trigger by turning the lock knob (lock pin). This trigger operated tool is intended for use only when a work contacting element is not practical due to the requirements of the application. Extreme caution must be maintained not to point the nosepiece of the tool in any unsafe direction. It must be firmly held against only an intended and substantial workpiece. c Lock knob ( I -ock pin) Ask Makita's Factory or Authorized service center for periodical inspection of the tool. i l- & SAVE THESE INSTRUCTIONS. 9 TOOL INSTALLATION INSTRUCTIONS AND USE Lubrication To insure maximum performance, install an air set (oiler, regulator, air filter) as close as possible to the tool. Adjust the oiler so that one drop of oil will be provided for every 50 nails. When an air set is not used, oil the tool with pneumatic tool oil by placing 2 (two) or 3 (three) drops into the air fitting. This should be done before and after use. For proper lubrication, the tool must be fired a couple of times after pneumatic tool oil is introduced. Loading nailer CAUTION : Always lock the trigger by turning the lock knob (lock pin) 90" and disconnect the hose before loading the nailer. To open the slide door, pull the door knob toward you while pushing up the leaf spring. . . . _ . . . . I Lock knob (Lock pin) E Slide door 10 Load nails into the magazine so that the nail points will be set into the groove at the bottom of the magazine. Move the nails into the ejection slot as far as they will go. CAUTION : Always load the same type and size of nail into the magazine. If you load the tool with different types and/or sizes a t the same time, a malfunction may result. To close the slide door, slide it toward the driver guide until the slide door is locked by the leaf spring. Adjusting depth of nailing CAUTION : Always lock the trigger and disconnect the hose before adjusting the depth of nailing. \ 3river guide / Groove The depth of nailing can be adjusted by moving the driver guide up or down. When moving the driver guide to the higher position, you can obtain a deeper depth of nailing; when moving it t o a lower position, you can obtain the shallower depth of nailing. To adjust the depth of nailing, proceed as follows: 1 . Remove hex wrench 3 from the hook. . 2. Turn the adjusting bolt with hex wrench 3 until the adjusting bolt contacts the projection of the center plate. I Hex wrench 3 I Projection of center plate I 1 1 3. Loosen the three screws which secure the driver guide a half turn. 4. Turn the adjusting bolt until the desired depth of nailing can be obtained. The adjusting bolt moves 0.7 mm ( 1 /32") per turn. 5. Tighten the three screws while holding the driver guide so that the projection of the center plate contacts the adjusting bolt. 6. If nails are driven too deep even when the driver guide is set a t the lowest position, decrease the air pressure. If nails cannot be driven deep enough even when the driver guide is set at the highest position, increase the air pressure. 4 e' Nose adapter CAUTION : Always lock the trigger and disconnect the hose before installing or removing the nose adapter. To prevent the workpiece from being damaged or scratched, attach the nose adapter to the end of the driver guide. When not using it, store it in either storage cavity in the inlet cap. Selecting compressor The air compressor must comply with the requirements of ANSI B19.3 - 1981. Select a compressor that has ample pressure and air output to assure ...