Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Securing the trigger in the ON po- sition is also very dangerous. Never attempt to fasten the trigger. Do not operate a tool ifany portion of the tool operating controls is inoperable, disconnected, altered, or not working properly. I Operate the tool within the specified air pressure of 4.5 -8.5 kgf/cm*G(65 -120 PSIG) for safety and longer tool life. Do not exceed the recom- 8 5 kgf/cm2G 8 5 kgf/cm2G (120 PSIG) (120 PSIG) mended max. operating pressure of 8.5 kgf/cmzG (120 PSIG). The tool should not be connected to a source whose pressure potentially exceeds 14.0 kgf/cmzG(200 PSIG). .Never use the tool with other than compressed air. If bottled gas (carbon dioxide, oxgen, nitro- gen, hydrogen, air, etc.) or combustible gas (hydrogen, propane, acetylene, etc.) is used as a power source for this tool, the tool will explode and cause serious injury. *Always check the tool for its overall condition and loose screws before operation. Tighten as required. Make sure all safety systems are inworking order before operation. The tool must not operate if only the trigger is pulled or if only the contact element is pressed against the wood. It must work only when both actions are performed. Test for possible faulty operation with nails unloaded. COMPRESSED AIR E .Make sure that the trigger is locked when the change lever is set to the LOCK position. Check walls, ceilings, floors, roofing and the like carefully to avoid possible electrical shock, gas leakage, explosions, etc. caused by striking live wires, conduits or gas pipes. Use only nails specified in this manual. The use of any other nails may cause malfunction of the tool. Do not permit those uninstructed to use the tool. *%-b 6 Change lever , Triggerlock Make sure no one is nearby before nailing. Never attempt to nail from both the inside and outside at the same time. Nails may rip through and/or fly off, presenting a grave danger. Watch your footing and maintain your balance with the tool. Make sure there is no one below when working in high locations, and secure the air hose to prevent danger if there is sudden jerking or catching. On rooftops and other high locations, nail as you move forward. It is easy to lose your footing if you nail while inching backward. When nailing against perpendicular surface, nail from the top to the bottom. You can perform nailing operations with less fatigue by doing so. A nail will be bent or the tool can become jammed if you mistakenly nail on top of another nail or strike a knot in the wood. The nail may be thrown and hit someone, or the tool itself can react dan- gerously. Place the nails with care. Do not leave the loaded tool or the air compressor under pressure for a long time out inthe sun. Be sure that dust, sand, chips and foreign matter will not enter the tool in the place where you leave it setting. @Donot point the ejection port at anyone in the vicinity. Keep hands and feet away from the ejection port area. @Whenthe air hose is connected, do not carry the tool with your finger on the trigger or hand it to someone in this condition. Accidental firing can be extremely dangerous. Handle the tool carefully as there is highpressure inside the tool that can be dangerous if a crack is caused by rough handling (dropping or strik- ing). Do not attempt to carve or engrave on the tool. Stop nailing operations immediately if you notice something wrong or out of the ordinary with the ... tool. *Always disconnect the air hose and remove all of the nails: 1. When unattended. 2. Before performing any maintenance or repair. 3.Before cleaning a jam. W?& 1 --- 4. Before moving the tool to a new location. I- Perform cleaning and maintenance right after finishing the job. Keep the tool in tip-top condi- tion. Lubricate moving parts to prevent rusting and minimize friction related wear. Wipe off all dust from the parts. *When not operating the tool, always lock the trigger by turning the change lever to the LOCK position. *Do not operate this tool if it does not contain a legible WARNING LABEL. *Do not modify tool without authorization from Makita. Ask Makita’s Factory or Authorized service center for periodical inspection of the tool. To maintain product SAFETY and RELIABILITY, maintenance and repairs should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. SAVE THESE INSTRUCTIONS. TOOL INSTALLATION INSTRUCTIONS AND USE Selecting compressor The air compressor must comply with the requirements of ANSI 619.3 -1981. Select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes place at a rate of approximately 40 times per minute at a compression of 6 kgf/cm2G (85 PSIG), a compressor with an air output over 95 l/minute is required. Pressure regu- lators must be used to limit air pressure to the rated pres- sure of the to...