Войти:
Оценок - 4, средний балл: 3.8 ( )

Инструкция по эксплуатации Makita, модель AG125

Производитель: Makita
Размер: 524.93 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Operate the tool within the specified air pressure of 4.5 -8.5 kgf/cm.G (65 -120 PSIG) for safety and longer tool life. Do not exceed the recommended max. operating pressure of 8.5 kgf/cm.G (120 PSIG). The toot should not be connected to a source whose pressure potentially exceeds 14.0 kgf/cm.G (200 PSIG). Never use the tool with other than compressed air. If bottled gas (carbon dioxide, oxgen, nitrogen, hydrogen, air, etc.) or combustible gas (hydrogen, propane, acetylene, etc.) is used as a power source for this toot, the tool will explode and cause serious injury. Always check the tool for its overall condition and loose screws before operation. Tighten as required. Nail guide Trigger Adjuster Gas pipe Live wire Make sure the safety system is in working order before operation. The tool must not operate if only the nail guide is pressed against the wood. Test for possible faulty operation with nails unloaded and the adjuster set to the number 1. Check walls, ceilings, floors, roofing and the like carefully to avoid possible electrical shock, gas leakage, explosions, etc. caused by striking live wires, conduits or gas pipes. Use only nails specified in this manual. The use of any other nails may cause malfunction of the tool. Do not permit those uninstructed to use the tool. Make sure no one is nearby before nailing. Never attempt to nail from both the inside and outside at the same time. Nails may rip through and /or fly off, presenting a grave danger. Nail Watch your footing and maintain your balance with the tool. Make sure there is no one below when working in high locations, and secure the air hose to prevent danger if there is sudden jerking or catching. On rooftops and other high locations, nail as you move forward. It is easy to lose your footing if you nail while inching backward. When nailing against perpendicular surface, nail from the top to the bottom. You can perform nailing operations with less fatigue by doing so. A nail will be bent or the tool can become jammed if you mistakenly nail on top of another nail or strike a knot in the wood. The nail may be thrown and hit someone, or the tool itself can react dangerously. Place the nails with care. Do not leave the loaded tool or the air compressor under pressure for a long time out in the sun. Be sure that dust, sand, chips and foreign matter will not enter the tool in the placewhereyou leaveitsetting. DO not point the ejection port at anyone in the vicinity. Keep hands and feet away from the ejection port area. Thump When the air hose is connected, do not carry the tool with your finger on the trigger or hand it to someone in this condition. Accidental firing can be extremely dangerous. Handle the tool carefully as there is high pressure inside the tool that can be dangerous if a crack is caused by rough handling (dropping or striking). Do not attempt to carve or engraveonthe tool. Stop nailing operations immediately if you notice something wrong or out of the ordinary with the tool. Always disconnect the air hose and remove the nail: 1. When unattended. 2. Before performing any maintenance or repair. 3. Before cleaning a jam. 4. Before moving the tool to a new location. Perform cleaning and maintenance right after finishing the job. Keep the tool in tip-top condition. Lubricate moving parts to prevent rusting and minimize friction related wear. Wipe off all dust from the parts. Do not operate this tool if it does not contain a legible WARNING LABEL. Do not modify tool without authorization from Makita. Ask Makita’s Factory or Authorized service center for periodical inspection of the tool. To maintain product SAFETY and RELIABILITY, mainte nance and repairs should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. SAVE THESE INSTRUCTIONS TOOL INSTALLATION INSTRUCTIONS AND USE Selecting compressor The air compressor must comply with the requirements of ANSI B19.3 -1981. Select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing frequency and compressor air output at a compression of 8.5 kgf/cm.G (120 PSIG). Thus, for example, when you drive about 10 nails 3.75 mm x 90 mm (0.148” x 3-1/2”) per minute, a compressor with an air output over 55 l/minute is required. Pressure regulators must be used to limit air pressure to the rated pressure of the tool where air supply pressure exceeds the tool’s rated pressure. Failure to do so may result in serious injury to tool operator or persons in the vicinity. NOTE: • Nail size indicates diameter x length. Selecting air hose Use an air hose as large and as short as possible to assure continuous, efficient nailing operation. With an air pressure of 5 kgf/cm.G (70 PSIG), an air hose with an internal diameter of over 8.5 mm (5/16”) and a length of less than 20 m (6.6 ft.) is recommended when the interval between each nailing is 0.5 seconds. Air supply hoses shall have a minimum w...

Эта инструкция также подходит к моделям:
Строительные пистолеты - AG090, AG125 (524.93 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории