Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Always use clean, dry compressed air with a maximum pressure of 200 psi. Use a pressure regulator and set the pressure between 70 – 120 psi. (5.0 – 8.5 kg/cm2G). Before each use, check the pressure regulator to ensure it is functioning within the proper pressure range. Using an air pressure of more than 120 psi can cause the angled finish nailer to malfunction or possibly explode causing severe injury or property damage. SELECTING A PROPER AIR HOSE Use an air hose with the largest diameter and shortest length possible to continuous, efficient nailing operations. Using an air pressure of 70 psi kg/cm2G), an air hose with an inside diameter of 1/4" (6.5 mm) or greater length of less than 6.6 ft (20 m), it is recommended that a 0.5 be allowed between each nailing. Air supply hoses shall have a of 150 psi (10.7 kg/cm2G) or 150% of the maximum pressure produced by the compressor or whichever is higher. Low air output by the compressor or a longer a smaller inside diameter in relation to the the driving capability of the air nailer. SELECTING A QUICK DISCONNECT 1. Remove the plastic protective from the tool’s air inlet. 2. Insert a 1/4" NPT male disconnect into the air 8 To improve the connection between the quick disconnect and air nailer, and to help prevent oxidation, apply PTFE tape or joint compound to the connector threads before insertion. 3. Snap the air hose onto the quick disconnect on the air nailer. Check for air leaks. LUBRICATION To ensure maximum performance, it is recommended to install an air set (oiler, regulator, and air filter) as close as possible to the air nailer. Adjust the oiler so that approximately one drop of oil will be released for every 50 nails. If an air set is not used or is unavailable, oil the tool using pneumatic tool oil by placing 2 or 3 drops into the air inlet. This should be done before and after use. For proper lubrication, the tool must be fired several times after the oil is introduced to the filter. OPERATING THE FINISH NAILER Always use hearing protection to protect your ears against hearing loss due to exhaust noise. Always wear proper safe-ty glasses to prevent injuries to the eyes from fragments of the work piece, defective nails or other debris caused by using the angled finish nailer. All safety glasses must have side shields and should conform to the requirements of the American National Standards Institute (ANSI) z87.1. Failure to comply with this warning could lead to serious or permanent to the ears as well as serious damage or permanent blindness in Always disconnect the air hose before making adjustments functionality of the air nailer. SELECT TRIGGER ACTUATION MODE The angled finish nailer is equipped with a selectable This allows the selection of Single Sequential Actuation Mode or Contact Actuation Mode. OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE To select the Single Sequential Actuation Mode (see Figure 1): 1. Press and hold the red Actuation Selector embedded in the trigger. 2. Rotate Actuation Selector down to the Single Sequential Actuation (T). 3. Release Actuation Selector, ensuring locking tab is fully seated in the slot. Figure 1 Ensure selector has locked into position. Ensure actuation process is fully understood before attempting to use angled finish nailer. TO USE THE ANGLED FINISH NAILER IN SINGLE SEQUENTIAL ACTUATION MODE: 1. Firmly grip angled finish nailer handle. 2. Position angled finish nailer work piece contact on work piece surface. 3. Push angled finish nailer against work piece compressing work piece contact. 4. Pull trigger on angled finish nailer to drive nail. The angled finish nailer will recoil away from the work piece as nail is driven. 5. Remove finger from trigger and lift angled finish nailer away from surface of work piece. OPERATION IN CONTACT ACTUATION MODE When using contact actuation mode, double fires resulting driven if the work piece contact piece. 9 10 To select Contact Sequential Actuation Mode (see Figure 2): 1. Press and hold Actuation Selector embedded in the trigger. 2. Rotate Actuation Selector up to the Contact Sequential Actuation (TTT). 3. Release Actuation Selector, ensuring locking tab is fully seated in the slot. Ensure selector has locked into position. Ensure actuation process is fully understood before attempting to use angled finish nailer. TO USE THE ANGLED FINISH NAILER IN CONTACT ACTUATION MODE: 1. Firmly grip angled finish nailer handle. 2. Pull and hold the angled finish nailer trigger. 3. Push angled finish nailer against work piece compressing work piece contact. 4. The angled finish nailer will drive nail upon contact. The angled finish nailer will recoil away from the work piece as nail is driven. ADJUSTING DEPTH OF NAILING Be aware of material thickness when using nailer. A protruding nail may cause injury. Adjust the depth of nailing by turning the adjustment knob (Figure 3, Item 1) to the left (A) for the deepest setting and to the right (B) for the shallowest setting. To increase t...