Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
After disconnecting the Stapler from the air compressor, there could still be enough air pressure to fire the Stapler. After the air compressor hose is disconnected, always fire the Stapler into a piece of scrap to make sure all of the air is expended. 1. Grip the Sleeve (78) and pull out the Magazine Cover (72). Caution: The Magazine Cover (72) may snap closed with force, sometimes without warning. 2. CleatsFIGURE 1Install fasteners: Cleats – Place the Cleats into the larger slot in the magazine so that the top of the cleat rests on the rail in the center of the magazine. See Figure 1, above. Staples – Place the staples over the center rail of the magazine. Note: Only use the fastener types and sizes listed on the Specifications Chart on page 2. 3. While holding the Sleeve (78) securely, slide the Magazine Cover (72) closed. Operation 1. Connect the Floor Stapler to the air hose and turn on the air compressor. Note: Before using on a floor, test the unit on a scrap piece of wood. Adjust the driving depth by providing more or less air pressure. Never exceed 125 PSI. Warning! Keep your feet clear of the Stapler. Refer to Figure 2. 2. Hold the Handle (44) securely with one hand and grip the Hammer with the other hand. FIGURE 33. Fasteners exit the Stapler from the bottom in the direction indicated above. HammerFace (1) (Striking this with the Trigger (33) held causes the stapler to fire.) Trigger (33) (This helps prevent unintentional firing.) FIGURE 2Make sure the Base Plate (52) is over the Fastener target position. Press down hard so that the Base Plate (52) is firmly contacting the floor. Then squeeze the Trigger (33) and strike the Hammer Face (1) with the Hammer to drive out a Fastener. Lift the tool off of the floor. See Figure 3. 4. Repeat the process until you are finished. Then, disconnect the Floor Stapler from the air source. Warning! After disconnecting the Stapler from the air compressor, there could still be enough air pressure to fire the Stapler. After the air compressor hose is disconnected, always fire the Stapler into a piece of scrap to make sure all of the air is expended. REV 11/06 Anytime any maintenance or repairs are done (including clearing jams), first: 1. Disconnect the Stapler from the air hose. 2. Empty Magazine (59, 69) completely. 3. Attempt to fire the Stapler into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any Fasteners. 4. Always leave Magazine Cover (72) closed during maintenance. The Magazine Cover is spring-loaded and may cause parts or a Fastener to fly out of the Stapler if it suddenly snaps closed. Clearing Jams 1. Disconnect tool from air hose, empty Magazine (59, 69) of Fasteners, release any built- up air pressure, and keep the magazine closed, as explained above. 2. While doing this step and the next, hold the Stapler pointed away from you and any other people or fragile objects. Remove all three Screws (49) and Washers (4) on the Driver Cover (48). See Figure 4. 3. FIGURE 4FIGURE 5Driver BladeCarefully lift the Driver Cover (48) off and remove the jammed Fastener. Pliers may be necessary to remove a stuck Fastener. 4. Inspect the Driver on the end of the Piston Assembly (26) for bends or breakage. If it is damaged, do not use the tool until it is repaired by a qualified technician. See Figure 5. 5. Lightly oil the driver and replace the Driver Cover (48). Make sure that the Driver Cover (48) fits in place flush and that the Driver does not get pinched by it. Replace and securely tighten all of the Screws (49) and Washers (4). 6. Reload the Stapler and reconnect it to the air hose. 7. Press the tip of the Stapler against an appropriate piece of scrap wood. 8. Test fire the Stapler several times, checking for proper operation. 9. Disconnect the Stapler, remove the Fasteners, and store the Stapler in a location out of children’s reach. Anytime any maintenance or repairs are done, first: 1. Disconnect the Stapler from the air hose. 2. Empty Magazine (59, 69) completely. 3. Attempt to fire the Stapler into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any Fasteners. 4. Always leave Magazine Cover (72) closed during maintenance. The Magazine Cover is spring-loaded and may cause parts or a Fastener to fly out of the Stapler if it suddenly snaps closed. Maintenance 1. Periodically lubricate all moving parts and pivots with a light oil. 2. Wipe down the Floor Stapler with a damp cloth. Do not use harsh detergents or solvents. 3. Check that the Base Plate (52) and the Hammer Face (1) is clear of any dirt or debris. Troubleshooting Note: Have the following problems repaired by a qualified service technician. PROBLEM CAUSE SOLUTION Air leaking in nose Loose Nose Screws Bumper is cracked/worn Tighten and recheck Replace Bumper Lack of Power, slow to cycle. Tool is too dry Air Pressure is too low Exhaust blocked Lubricate Check air supply equipment Clean exhaust channel Intermittent feeding or no fast...