Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Connect the Air Source Hose to the Air Plug (41). Note: If you are not using an automatic oiler system on your air compressor, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Remove the air line at the inlet and put 2 or 3 drops of good quality air tool oil into the air fitting each day of use. With heavy, prolonged use, do this at least twice a day. 2. Set the air pressure on your compressor to 60-125 PSI. Do not exceed the maximum air pressure of 125 PSI. Note: About Air Consumption -CFM Air fastening tools are classified as “intermittent use”, and, as such, may be operated by compressors of almost any size. Small, portable units may not be suitable for high volume work, but will satisfactorily power the nailer for work at a slower rate. The air demand of any fastening tool depends largely upon how quickly the tool is to be used. PRESSURE - Use the lowest air pressure that will sufficiently drive the fastener into the wood. This will depend on the density of the wood, and upon the size and length of the nails being used. Vary the air pressure to adjust the driven depth, without exceeding hte maximum air pressure of 125 PSI. 3. Check the air connection for leaks. REV 11/06 SKU 46240-B For technical questions, please call 1-800-444-3353. Page 5 Testing the Full Sequential Safety Trip Mechanism Warning: Even though the nailer should be empty during this procedure, ALWAYS point the nailer at a piece of scrap wood when testing. 1. Make sure the tool is disconnected from the power supply. 2. Completely empty the Magazine (56) of nails. 3. The Nailer should not fire if the Safety (28) is not depressed against the workpiece. 4. Make sure the Trigger (31) and Safety (28) move freely, without sticking. 5. Connect the air supply to the tool at the Air Plug (41). Set the regulator at the recommended 60 to 125 PSI. 6. Test the tool by depressing the Safety (28) against the workpiece without pulling the Trigger (31). The Tool must not cycle (fire). If it cycles (fires), stop immediately and have it repaired by a qualified service technician. 7. Hold the tool away or off of the workpiece. The Safety (28) of the tool should return to its original position. Point the nailer in a safe direction, towards the scrap wood and squeeze the Trigger (31). The tool should not cycle (fire). If the tool fires, stop immediately and have it repaired by a qualified service technician. 8. Depress the Safety (28) against the workpiece and squeeze the Trigger (31). The tool must cycle (fire) only once. Release the Trigger and squeeze it again. The tool must not cycle (fire). With the Trigger held, carefully lift the nailer and press it against the workpiece again. The tool must not cycle (fire). If it fails to perform in the manner explained in bold, have it repaired by a qualified service technician. Use the Correct Type of Nails This nailer uses only “clipped-head” nails, which are collated at an angle of 28°. “Round Head” nails, collated at 22°, are not to be used in this tool, as they will not feed reliably, and may cause premature wear of the driver assembly. Harbor Freight tools offers a variety of compatible fasteners, which are usually collated in strips of 25. Nails from other manufacturers are also widely available from home centers and building supply stores. Please note that some manufacturers offer fasteners packaged for their brand of air nailers, and their nail strips may be longer than the loading slot in this tool. REV 11/06 SKU 46240-B For technical questions, please call 1-800-444-3353. Page 6 Loading Nails ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other people in the work area must also wear ANSI approved impact safety goggles. Always disconnect the air nailer from the air supply when loading the magazine. Grasp the finger grip at the lower left side of the magazine, and pull the slide firmly back until it latches. (See the photo section below.) Insert a strip of clipped-head nails, point down, into the loading slot on top of the magazine. You may load 3, or more, strips, depending on the size of the nails. When ready, pull rearward on the finger grip to relieve spring tension, and press the magazine latch in to release the slide. Hold the slide grip to allow it to close gently. Photo Photo 2 1 Photo Photo 4 3 Operating the Nailer 1. Attach the Nailer to the air supply at the Air Plug (41). Start your compressor and check the pressure making sure it is set at the recommended 60-125 PSI and not over the maximum 125 PSI. 2. After reading the following, it is recommended that you get acquainted with this tool by practicing on scrap wood until you are familiar with its characteristics. Always Wear Eye Protection When Using the Air Nailer 3. Turn the Exhaust Cover (4) to direct the air away from the operator. 4. The full sequential trip trigger has a safety device assembled to the nosepiece. The nailer will not fire unless th...