Оценок - 5, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
10401 • Rust resistant chrome finish SAFETY INFORMATION WARNING: Follow all safety warnings listed below and throughout manual. Improper use of this tool can cause severe injury. 1. Read and understand this manual before loading or using tool. 2. Make certain you read and understand all Warnings. 3. Only well-instructed adults should use tool. Never allow children to use tool. 4. Wear safety glasses to protect your eyes. 5. Do not alter this tool in any way. 6. Always store tool with staples removed and out of children’s reach. 7. Keep this manual for reference. It is your guide to safe and proper operation of this tool. PRODUCT IDENTIFICATION Head Assembly Comfort Grip Staple Feed Cap Magazine Assembly Hinge Screw/Nut HOW TO USE Grasp the comfort grip and with a quick movement, strike the surface squarely (similar to using a hammer). HOW TO LOAD 1. Push staple feeder assembly forward and slide staple feed cap upward (see Figure 1). 2. Pull staple feeder assembly out of hammer tacker. 3. Insert strip of staples, points down, into staple channel (see Figure 2). 4. Replace staple feeder assembly into handle with U-channel facing down. Staple Feed Cap Step 1 Step 2 Push In Push Up Figure 1 - Removing Staple Feeder Assy. Staple Feeder Assembly 5. Push forward and lock staple feed cap in place. HOW TO DISASSEMBLE 1. Remove staple feeder assembly and staples as indicated in loading instructions. 2. Using a 7mm wrench and a philipshead screwdriver, remove nut from hinge screw. 3. Grasp tool at the head assembly and compress magazine assembly slightly (see Figure 3, page 3). Figure 2 - Installing Staples and Staple Feeder Assy. Magazine Assembly Staples (Points Down) Staple Feeder Assembly 113267 2 4. Pull (remove) hinge screw from tool handle. 5. Release magazine assembly and slide forward from head assembly (see Figure 4). The hammer tacker is now completely apart and ready for cleaning. Also, jams may be cleared when taken apart. Take care not to damage the exposed staple driver. HOW TO ASSEMBLE Reverse the above procedure. Align the staple driver with the channel opening at the head of the magazine assembly. Compress magazine assembly slightly to align holes for the hinge screw and insert screw. Note:The hinge screw may be inserted from either side of handle. Fasten nut onto hinge screw securely. Head Assembly Pull Magazine Assembly Magazine Assembly Compress Figure 3 - Compress Magazine Assy. Figure 4 - Removing Magazine Assy. ST APLES Staple Brand Staple Siz es 1/4" 5/16" 3/8" PowerFast® P-A11-1/4 36504A P-A11-5/16 36505A P-A11-3/8 36506A Arrow® 504 505 506 Bostitch® TRA704 TRA705 TRA706 Duo-Fast® A11 04C A11 05C A11 06C Rapid® A11 1/4 A11 5/16 A11 3/8 Senco® H04 H05 H06 PowerFast® is a registered trademark of DESA IP, LLC. Arrow® is a registered trademark of Arrow Fastener Company, Inc. Bostitch® is a registered trademark of Stanley-Bostitch, Inc. Duo-Fast® is a registered trademark of Duo-Fast Corporation. Rapid® is a registered trademark of Isaberg Rapid AB. Senco® is a registered trademark of Senco Products, Inc. 113267 3 TECHNICAL SERVICE You may have further questions about assembling, operating, or maintaining this product. If so, you can visit our Technical Service web site at or contact our Technical Service Department at 1-800-858-8501 (English Only). You may also write to: DESA Specialty Products™ ATTN: Technical Service Specialty Products P.O. Box 90004 Bowling Green, KY 42102-9004 When contacting DESA Specialty Products ™, have ready •Your Name •Your Address •Your Phone Number • Model Number of Product • Date of Purchase (Include copy of receipt for written requests). LIMITED WARRANTY DESA Specialty Products™ warrants model number 10401 Hammer Tacker for a period of 90 days from date of purchase against original defects in materials or workmanship. If this product fails to perform for either of those reasons, DESA Specialty Products™will replace the tool, at DESA Specialty Products’ ™ option, with an equivalent product. This warranty gives you specific legal rights. You may also have other rights, which vary from state to state or province to province. To obtain the benefits of the warranty, contact DESA Specialty Products™ Technical Services Department at the address or number listed below. The bill of sales or proof of purchase must be presented at the time a claim is made. Bowling Green, KY 42102-9004 800-858-8501 (English Only) Industries of Canada, Inc. 2220 Argentia Road Unit #4 Mississauga, Ontario L5N 2K7 800-561-3372 / 905-826-8010 FAX 905-826-8236 Printed in Taiwan 113267 4 Grapadora de martillo Instrucciones de operacion CARACTERISTICAS • Mas rapida y sencilla que una grapadora regular. • Ideal para engrapar en su sitio grandes ...