Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Trigger This tool has an easy squeeze trigger. The trigger is located underneath the hand grip. Each squeeze of the trigger fires one staple. Make sure your finger is not on the trigger when connecting or loading the tool. ON/OFF Trigger Lock This tool is equipped with a sliding ON/OFF trigger lock. The trigger lock is located at the front of the hand grip, just above the trigger. This safety feature helps prevent accidental firing. Make sure the trigger lock reads OFF when plugging in or loading the tool. Also, make sure the trigger lock reads OFF when tool is not in use. To release, slide the trigger lock to read ON. Extension Cords ! CAUTION: Use only extension cords marked for outdoor use. Be sure to use the right size extension cord. If cord size is wrong, tool may be damaged. Tool performance may also be affected. Extension Cord Size Requirement 1 to 25 feet, use 16 AWG rated cord 26 to 50 feet, use 14 AWG rated cord Inspect extension cord often. Replace cord if worn or damaged. Loading Tool ! WARNING: Never load tool while it is plugged in. Accidentaldischarge may occur. Before loading, move trigger lock to the OFF position and unplug tool. Figure 2 Figure 3 Figure 1 Trigger Lock In Off Position 1. Move trigger lock to the OFF position (see Figure 1) and unplug tool. 2. Turn tool upside down. 3. Press in latch lock and slide staple chamber cover back until fully open (see Figures 2 and 3). Staple Chamber Cover Latch Lock Continued 4. Drop staples in channel (see Figure 4). Note:We recommend that you only use PowerFast or Swingline heavy- duty staples in this tool. Wrong staples can cause jamming. Slide staple chamber cover closed. Make sure cover locks into place. Figure 4 Staples Operating Tool ! WARNING: Keep trigger lock in the OFF position and finger offtrigger until ready to drive staple. ! WARNING: Keep all body parts away from staple exit on tool. Trigger 1. Make sure trigger lock is in the OFF position. 2. Plug tool into a 115 Volt/60 Hertz outlet. 3. Grip tool firmly. 4. Slide trigger lock to the ON position. Lock Figure 5 5. Squeeze trigger to fire. 6. IMPORTANT: Do not fire this tool when empty of staples. This may damage tool. Note: In difficult fastening jobs, press down on head of tool with palm of free hand (see Figure 6). This will improve staple driving. Tool Jam 1. If tool jams, move trigger lock to the OFF position and unplug tool. 2. Turn tool upside down. 3. Press in latch lock and slide staple chamber cover back until fully open. 4. Remove unused staples. 5. Remove staple(s) causing jam. 6. Reload tool (see Loading Tool, page 5). Cleaning Use a clean cloth to remove dirt from tool. Do not use solvents when cleaning plastic parts. Lubrication Do not oil or grease any part of tool. This may damage tool. IMPORTANT: Do not attempt to repair tool or replace broken parts. Any servicing, except what is listed above, should be done by an our factory service center. Figure 6 Maintenance ! WARNING ICON G 001 WARNING: Do not alter this tool in any way. Only use accessories designed for this tool. ! WARNING ICON G 001 WARNING: Never perform steps listed below while tool is plugged in. Accidental discharge may occur. Move trigger lock to the OFF position and unplug tool. Staples We recommend that you only use PowerFast or Swingline heavy-duty staples. These staples are available in six lengths. PowerFast or Swingline heavy-duty staples can be found where you purchased your staple gun. Part Number Length 36804 (800-4) 1/4" 36805 (800-5) 5/16" 36806 (800-6) 3/8" 36808 (800-8) 1/2" 36810 (800-9LT) 9/16" Swinglinea is a registered trademark of ACCO World Corporation. LIMITED ONE YEAR WARRANTY DESA Industries warrants this product for a period of one year from date of purchase against original defects in materials or workmanship. If this product fails to perform for either of those reasons, DESA Industries will repair or replace with an equivalent product at no charge within 45 days of receipt of the defective product. This warranty gives you specific legal rights. You may also have other rights, which vary from state to state. To obtain the benefits of this warranty if the product fails due to defects in materials or workmanship, contact: DESA Industries of Canada, Inc. Unit #4 2220 Argentia Road Mississauga, Ontario L5N2K7 a PISTOLET AGRAFEUR ELECTRIQUE Modele 34310 GUIDE D’UTILISATION Consignes de securite ! AVERTISSEMENT : Respectez toutes les consignes de securite decrites dans le present guide. Une utilisation inappropriee de cet outil peut causer des blessures graves ou meme la mort, etant donne le risque d’incendie, de choc electrique ou de decharge d’une agrafe dans le corps. Avant l’utilisation de l’outil 1. Lisez et comprenez les presentes instructions. 2. Seuls les adultes bien informes devraient utiliser cet outil. Ne laissez jamais un enfant l’utiliser. 3. Evitez d’utiliser l’outil : • en presence de liquides ou de gaz hautement inflammables • sous l’influence de l’alcool, de drogue...