Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Always disconnect air from stapler whenever servicing! During maintenance, a stapler connected to air may fire accidentally, causing serious personal injury! To replace a piston: 1. Disconnect the stapler from the air supply! 2. Remove all staples from the magazine cartridge. 3. Remove the 4 cap screws from the stapler exhaust cap on the Model H5626, or unscrew the exhaust cap on the Model H5627. 4. Remove the exhaust cap as shown in Figure 6. 5. The top of the piston should now be visible inside the cylinder, which is housed in the head of the stapler. 6. Open the magazine. Figure 6. Removing stapler exhaust cap. 7. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. 8. With a long flathead screwdriver or similarly shaped tool, push the piston shaft back inside the stapler until you can grip the piston head and remove it from the cylinder. (Be careful not to scratch the discharge area when pushing the piston shaft with the screwdriver.) 9. Place a new O-ring on the new piston and apply a thin film of the stapler lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide. The new piston should easily slide into the cylinder. Do not force the piston into the cylinder! If the piston is not easily inserted, double- check the alignment of the piston shaft with the grooves on the guide. 11. After the piston is inserted correctly, close the magazine. Replace the rear cap assembly and tighten the 4 cap screws. 12. For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual. -10- H5626/H5627 Upholstery Stapler MAINTENANCE NOTES H5626/H5627 Upholstery Stapler -11 -12- H5626/H5627 Upholstery Stapler H5626 PART BREAKDOWN 14 13 59 12 8 7 6 5 19 11 1 34 21 4 1 20 23 42 41 36 39 22 38 43 45 52 56 45 60 32 31 33 61 55 66 30 29 28 26 27 25 24 9 3 18 64 65 23 62 7 71 33 REF PART # DESCRIPTION REF PART # DESCRIPTION 01 PSB95M CAP SCR M5-.8 X 30 03 PH5626003 CAP COVER 04 PH5626004 SPRING 05 PH5626005 SEAL 06 PH5626006 CAP 07 PH5626007 O-RING 08 PH5626008 HEAD VALVE ASM. 09 PH5626009 O-RING 11 PH5626011 O-RING 12 PH5626012 COLLAR 13 PH5626013 O-RING 14 PH5626014 DRIVER ASSEMBLY 18 PH5626018 CYLINDER 19 PH5626019 BUMPER 20 PH5626020 BODY 21 PH5626021 DRIVER GUIDE 22 PH5626022 PIN 23 PEC01M E-CLIP 3MM 24 PH5626024 SEAL 25 PH5626025 TRIGGER VALVE HD 26 PH5626026 TRIGGER VALVE STEM 27 PH5626027 O-RING 28 PH5626028 O-RING 29 PH5626029 TRIGGER VALVE GUIDE 30 PH5626030 TRIGGER 31 PH5626031 O-RING 32 PH5626032 TUBE 33 PH5626033 O-RING 34 PSB17M CAP SCR M4-.7 X 10 36 PH5626036 NOSE 38 PH5626038 MAGAZINE 39 PH5626039 SET PLATE 41 PH5626041 PUSHER 42 PH5626042 STAPLE GUIDE UNIT 43 PH5626043 SPRING 45 PSB114M BTN HD CAP SCR M4-.7 X 8 52 PH5626052 END CORE ASM. 55 PSB15M CAP SCR M5-.8 X 20 56 PH5626056 BRACKET 59 PH5626059 SET PLATE 60 PLN02M LOCK NUT M5-.8 61 PH5626061 1/4" NPT CONNECT 62 PH5626062 PIN 64 PH5626064 SPRING 65 PH5626065 TRIGGER 66 PH5626066 SPRING 67 PSB18M CAP SCR M4-.7 X 8 71 PH5626071 AIR ROOM H5626/H5627 Upholstery Stapler -13 -14- H5626/H5627 Upholstery Stapler H5627 PART BREAKDOWN B A A 7 9 30 1 2 3 4 5 6 29 31 33 19 18 15 17 16 14 13 12 11 10 20 21 22 B 59 60 62 61 21 67 15 64 63 60 15 65 66 C C 23 25 35 34 36 37 40 42 41 43 44 38 48 46 39 47 70 55 56 45 73 68 69 73 32 26 28 27 71 8 72 REF PART # DESCRIPTION REF PART # DESCRIPTION 01 PH5627001 CAP 02 PH5627002 O-RING 03 PH5627003 CYL. PRESS RING 04 PH5627004 O-RING PH5627005 CYLINDER 06 PH5627006 O-RING 07 PH5627007 O-RING 08 PH5627008 DRIVER ASSEMBLY 09 PH5627009 BUMPER PH5627010 COLLAR 11 PH5627011 O-RING 12 PH5627012 VALVE 13 PH5627013 VALVE PLUNGER 14 PH5627014 O-RING PH5627015 O-RING 16 PH5627016 COLLAR 17 PH5627017 O-RING 18 PH5627018 O-RING 19 PH5627019 VALVE PLUNGER PH5627020 O-RING 21 PH5627021 O-RING 22 PH5627022 O-RING 23 PH5627023 O-RING PH5627025 PLUNGER CAP 26 PH5627026 TRIGGER 27 PH5627027 PIN 28 PH5627028 O-RING 29 PH5627029 BODY PH5627030 DRIVER GUIDE 31 PH5627031 EXHAUST DIFFUSER 32 PH5627032 COVER 33 PH5627033 1/4" NPT CONNECT 34 PSB23M CAP SCR M4-.7 X 12 35 PSB53M CAP SCR M5-.8 X 18 36 PH5627036 NOSE 37 PH5627037 SET PLATE 38 PH5627038 MAGAZINE 39 PH5627039 SHAFT 40 PH5627040 STAPLE GUIDE UNIT 41 PH5627041 SET PLATE 42 PH5627042 PUSHER 43 PH5627043 SPRING 44 PSB114M BTN HD CAP SCR M4-.7 X 8 45 PH5627045 END CORE ASM. 46 PH5627046 BRACKET 47 PSB24M CAP SCR M5-.8 X 16 48 PSB23M CAP SCR M4-.7 X 12 55 PH5627055 SET PLATE 56 PH5627056 FLT HD SCR M4-.7 X 6 59 PH5627059 PLUNGER 60 PH5627060 O-RING 61 PH5627061 O-RING 62 PH5627062 SLEEVE 63 PH5627063 SPRING 64 PH5627064 PLUNGER 65 PH5627065 PLUNGER CAP 66 PH5627066 SPRING 67 PH5627067 REGULATOR ASM. 68 PH5627068 PILOT SLEEVE 69 PH5627069 RAPID FIRE ADJ KNOB 70 PH5627070 SET BLOCK 71 PFH33M FLT HD SCR M4-.7 X 11 72 PLN01M LOCK NUT M4-.7 73 PH5627073 O-RING H5626/H56...
Эта инструкция также подходит к моделям:Строительные пистолеты - H5627 (695.18 kb)