Оценок - 6, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Clear all ports and blow the solvent away with compressed air. 9. Replace any part that shows damage or heavy wear. Relubricate the tool. 10. Apply a thin film of the stapler lubricating oil on the new O-ring and place it on the new piston. Install any other parts included in the piston repair kit. 11. Insert the new piston in the cylinder. With the magazine cover open, gently push the piston down to make sure the piston driver moves freely into the driving hole. Note: DO NOT force the piston into the cylinder! If the piston 'hangs' in the cylinder, double check the fit between piston and O-ring and make sure the cylinder is clean. 12. Make sure that the cap gasket is in place, then secure the cap to the stapler body by tightening the four cap screws. -12- H7947/H7948 16 Gauge Stapler CLEANING & LUBRICATING Cleaning Use an automotive grade solvent such as Sprayway C-60® (G2544 in the Grizzly catalog) to clean the nose assembly of the stapler. Always be sure that the stapler is dry before using it again. Do not allow dust, chips, or sand into the air connectors or into the body of the stapler; this may result in leaks and damage to the stapler and the air couplings. Never use gasoline to clean this tool. Use extreme caution when using any solvent cleaner. Always clean the tool in a well-ventilated area and never if sparks or open flames are present. Remember that electrical machinery in the area can produce sparks during normal operation. Ignoring this warning can cause serious personal injury or even death! Lubricating Special pneumatic tool oil has been included with your new Grizzly stapler to help maintain its useful life. Place two to six drops of oil in the stapler air inlet (as shown in Figure 13) every two hours of continuous use. Wipe off any excess oil near the stapler exhaust to avoid dust build-up. When the oil that was included with your stapler has been completely used, replace with Grizzly Model G2820 Pneumatic Tool Oil. An efficient alternative to oiling your tool by hand is to install a lubricator in your air compressor line. If your air compressor line already has a lubricator, then regular lubrication of your stapler will not be necessary. Just make sure there is always oil in the lubricator. Figure 13.Lubricating the stapler at the air inlet. H7947/H7948 16 Gauge Stapler -13 -14- H7947/H7948 16 Gauge Stapler H7947 PARTS BREAKDOWN .................................................................................................................. ...................................................................................................... ............ .......... ...................... .............. .. .. .. .. .. .. .. .. .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... H7947 PARTS LIST REFPART # DESCRIPTION REFPART # DESCRIPTION 1 PFH06M FLAT HD CAP SCR M6-1 X 20 2 PH7947002 FRONT BRACKET 3 PH7947003 EXHAUST COVER PH7947005 EXHAUST FILTER PLATE 6 PSB38M CAP SCREW M5-.8 X 25 7 PH7947007 CAP 8 PH7947008 SPRING 9 PH7947009 O-RING PH7947010 WASHER 11 PH7947011 PISTON HEAD VALVE 12 PH7947012 O-RING 13 PH7947013 SEAL 14 PH7947014 PLAIN WASHER PH7947015 PISTON STOPPER 16 PH7947016 O-RING 17 PH7947017 PISTON 18 PH7947018 DRIVER 19 PH7947019 CYLINDER PH7947020 O-RING 21 PH7947021 CYLINDER RING 22 PH7947022 COLLAR 23 PH7947023 O-RING 24 PH7947024 GASKET PH7947025 BODY 26 PH7947026 PAD 27 PH7947027 SET PLATE 28 PH7947028 BOTTOM BUMPER 29 PRP97M ROLL PIN 3 X 30 PH7947030 RUBBER GRIP 31 PSB24M CAP SCREW M5-.8 X 16 32 PH7947032 O-RING 33 PH7947033 COVER 34 PH7947034 SPRING PH7947035 TRIGGER PLATE 36 PH7947036 TRIGGER 37 PRP02M ROLL PIN 3 X 16 38 PH7947038 SLIDE SHAFT 39 PH7947039 TRIP GUIDE PH7947040 SPRING 41 PH7947041 CONTACT TRIP BLOCK 42 PH7947042 ADJUSTING BLOCK 43 PH7947043 CONTACT ARM 44 PSB33M CAP SCREW M5-.8 X 12 45 PH7947045 DRIVER GUIDE PLATE 46 PRP04M ROLL PIN 4 X 24 47 PSB79M CAP SCREW M5-.8 X 32 48 PH7947048 SET BLOCK 49 PH7947049 CAP SCREW M3-.6 X 16 50 PH7947050 NOSE 51 PH7947051 MAGAZINE COVER 52 PH7947052 STAPLE GUIDE 53 PSB33M CAP SCREW M5-.8 X 12 54 PH7947054 SPRING 55 PH7947055 STOPPER 56 PH7947056 BUTTON HD CAP SCR M5-.8 X 60 57 PH7947057 MAGAZINE 58 PH7947058 SPIRAL SPRING 59 PH7947059 FLAT HD SCR M3-.5 X 5 62 PH7947062 PUSHER GUIDE 63 PH7947063 O-RING 64 PH7947064 O-RING 65 PH7947065 TRIGGER VALVE HOUSING 66 PH7947066 BALL PIN 67 PH7947067 O-RING 68 PH7947068 PILOT VALVE 69 PH7947069 O-RING 70 PH7947070 O-RING 71 PH7947071 SPRING 72 PH7947072 PLUNGER 73 PH7947073 O-RING 74 PH7947074 TRIGGER VALVE CAP 75 PH7947075 O-RING 76 PW02M FLAT WASHER 5MM 77 PH7947077 MACHINE LABEL 78 PH7947078 STAPLER CASE 79 PH7947079 INCLUDED PNEUMATIC OIL 80 PAW04M INCLUDED HEX WRENCH 4MM 81 PH7947081 PISTON REPAIR...
Эта инструкция также подходит к моделям:Строительные пистолеты - H7948 (1.85 mb)