Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
BOSTITCH cannot assume responsibility for product performance if our tools are used with fasteners or accessories not meeting the specific requirements established for genuine BOSTITCH fasteners and accessories. TOOL SETUP The MFN-201 was designed to install 1/2” to 3/4” tongue and groove hardwood flooring. The tool is factory set for 3/4” flooring. Two additional foot plates are included with this tool to accommodate 1/2” and 5/8” flooring. Flooring products will vary and the user must ensure the tool is properly adjusted each time flooring is being installed. Dimensions listed on the footplates are suggestions.Test fastener placement on scrap pieces of wood before installing floor. To change footplates: 1. Remove 4 flat head cap screws. 2. Change to desired plate. 3. Replace 4 flat head cap screws. Flat head cap screws FASTENER PLACEMENT: Too High Correct Too Low 4 LOADING THE MFN-201 EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection. TO PREVENT ACCIDENTAL INJURIES: • Never place a hand or any other part of the body in nail discharge area of tool. • Never point the tool at anyone else. • Never engage in horseplay. • Always handle the tool with care. • Do not contact the actuator while loading the tool. LOADING THE TOOL 1. Release the pusher spring clip and remove the pusher blade. 2. Load the fasteners into guide channel. 3. Insert rounded end of pusher blade into channel to retain fasteners. 4. Latch pusher spring clip to notched end of pusher blade. Ensure sufficient engagement of pusher blade for smooth fastener feeding. 1. 2. 4..3. FASTENER MAY NOT FEED CONSISTENTLY IF PUSHER BLADE IS NOT INSTALLED. BEFORE HANDLING OR OPERATING THIS TOOL READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL. 5 OPERATION EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection. The MFN-201 was designed to install 1/2” - 3/4” tongue and groove hardwood flooring. NOTE: Always test on a scrap piece of flooring. CAUTION: NEVER HIT THE PLUNGER WITH THE METAL END OF THE MALLET. 1. Position the flooring per the manufacture’s specifications. 2. Place the tool with the guide plate above the tongue and firmly against the forward face of the flooring material. 3. Ensure that the composite foot is firmly held against the top surface of the flooring. 4. Using the rubber face of the mallet strike the top end of the metal plunger. 2. 4. NOTE: Sufficient force is required to completely drive a single fastener with one strike of the mallet. NOTE: REGARDING THE USE OF THIS TOOL TO INSTALL PRE-FINISHED FLOORING The BOSTITCH MFN-201 has been precisely engineered to be compatible with today’s vast array of hardwood flooring products, including pre-finished flooring. Due to the ever changing products and manufacturing processes used in producing pre-finished hardwood flooring, caution must be used to ensure that the flooring finish is not damaged by the tool. Always test the tool and installation technique on a sample section of flooring to be certain that both the tool and the installation technique do not damage the pre-finished flooring. This procedure should be followed before each job due to variations in flooring and tool condition. BOSTITCH cannot assume responsibility for any flooring damage. RATCHET OPERATION To change drive mode: 1. Remove the cotter pin and then the clevis pin. 2. Position ratchet mechanism. • For ratcheting (multi-blow) operation, set as shown in Fig. 1. • For non-ratcheting (single-blow) operation, set as shown in Fig. 2. 3. Replace clevis pin and the cotter pin after adjustment. NON- RATCHETING clevis pin Fig. 1 RATCHETING cotter pin Fig. 2 6 FASTENER DEPTH UNDER DRIVEN FASTENER PROPERLY DRIVEN FASTENER Floor Fastener Sub Floor If the plunger does not fully return the nail ...