Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
© 2007 Nailer Components And Specifications HD219000 HD289000 • REQUIRES (SCFM with 16 nails 4.1 4.1 per minute @ 90 psi) • AIR INLET 1/4 inch NPT 1/4inch NPT • NAIL LENGTH 2 inch 2 inch RANGE to 31.2 inch to 31.2 inch • NAIL SHANK 0.113 inch to 0.113 inch to RANGE 0.131 inch 0.131 inch • MAGAZINE CAPACITY 60-75 75-105 • WEIGHT 8 lbs. 5 oz. 8 lbs. 15 oz. • LENGTH 19.5 inch 21.75 inch • HEIGHT 15 inch 15 inch • MAX PRESSURE 120 psi 120 psi • PRESSURE RANGE 70 - 120 psi 70 - 120 psi HD349000 4.1 1/4 inch NPT 2 inch to 31.2 inch 0.113 inch to 0.131 inch 75-105 8 lbs. 11 oz. 19.75 inch 15 inch 120 psi 70 - 120 psi Adjustable Direction Threaded Hole/Tool Exhaust Deflector Balancer (M8 x 1.25) Nail Loading Area Single Cycle Trigger Magazine Warning Labels Nail Discharge Area Work Contact Element Models HD219000, HD289000, & HD349000 Safety Guidelines (Continued) . Do not modify or alter the nailer or any nailer parts. Do not use the nailer if any shields or guards are removed or altered. Do not use the nailer as a hammer. Personal injury or tool damage may occur. . Avoid long extended periods of work with the nailer. Stop using the nailer if you feel pain in hands or arms. . Always check that the Work Contact Element (WCE) is operating properly. A nail could accidentally be driven if the WCE is not working properly. Personal injury may occur (See "Checking the Work Contact Element" Section). . Disconnect air supply and release tension from the pusher before attempting to clear jams because fasteners can be ejected from the front of the nailer. Personal injury may occur. . Avoid using the nailer when the magazine is empty. Accelerated wear on the nailer may occur. . Clean and check all air supply hoses and fittings before connecting the nailer to an air supply. Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced. . Air compressors providing air to the nailer should follow the requirements established by the American National Standards Institute Standard B19.3-1991; Safety Standard for Compressors for Process Industries. Contact your air compressor manufacturer for information. Recommended Hookup Operating The Nailer Read this manual and understand all safety warnings and instructions before operating the nailer. LUBRICATION This nailer requires lubrication before using the nailer for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis. The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibil- ity. Failure to lubricate the nailer properly will dramatically shorten the life of the nailer and void your warranty. 1. Disconnect the air supply from the nailer to add lubricant. 2. Turn the nailer so the air inlet is facing up. Place 4-5 drops of 30 W non- detergent oil into air inlet. Do not use detergent oils, oil additives, or air tool oils. Air tool oils contain solvents which will damage the nailer’s internal components. OIL 3. After adding oil, run nailer briefly. Wipe off any excess oil from the cap exhaust. RECOMMENDED HOOKUP 1. The air compressor must be able to maintain a minimum of 70 psi when the nailer is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 70 psi Min. 120 psi Max. 2. An oiler can be used to provide oil circulation through the nailer. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the nailer. 3. Use 3/8 inch air hoses with a minimum working pressure of 150 psi. Use 1/2 inch air hoses for 50 foot run or longer. For better performance, install a 3/8 inch quick plug (1/4 inch NPT threads) with an inside diameter of .315 inch (8mm) on the nailer and a 3/8 inch quick coupler on the air hose. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the nailer between 70 and 120 psi. Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Oiler RegulatorQuick Plug Filter 3 Operating Instructions Operating The Nailer (Continued) NO-MAR DECKING TIP The no-mar decking tip is designed to eliminate marks caused by the serrated work contact element (WCE). The no- mar tip may be removed if not required (See REMOVING NO-MAR DECKING TIP). Use tool in single cycle mode (SEE OPERATIONAL MODES) when no-mar tip is in place. REMOVING NO-MAR DECKING TIP 1. Disconnect air supply from nailer. 2. Remove all fasteners from magazine (See UNLOADING THE NAILER). 3. Remove no-mar tip retaining ring. Retaining Ring No-Mar Tip 4. Pry no- mar tip away from the work contact element. Work Contact Element No- Mar Tip 5. Replace retaining ring onto no-mar tip, then store tip in safe place for future use. INSTALLING NO-MAR DECKING TIP 1. Disconnect air supply from nailer. 2. Remove all fasteners from magazine (See UNLOADING THE NAILER). 3. Remove re...
Эта инструкция также подходит к моделям:Строительные пистолеты - HD219000 (1.59 mb)
Строительные пистолеты - HD289000 (1.59 mb)