Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Icon Description Purpose 20 . Cone nozzle Welding, shrink sleeving (heat concentrated over small area) 50 mm Fish tail Drying, thawing surface nozzle (heat spread over wide area) 1. Make sure the on/off switch (A) is in position "O" and the is disconnected from the power source. Ensure the nozzle cooled down. 2. Place the desired accessory onto the nozzle. 6 OPERATION WARNING: Make sure the nozzle ALWAYS points away from you and any bystanders. WARNING: DO NOT drop anything into the nozzle. WARNING: Use only one hand to hold the tool as shown in Figure 2. Do not place your other hand over the air vents (Fig. 3). FIG. 2 FIG. 3 PRIOR TO OPERATION 1. Attach the correct accessory recommended for the application. 2. Turn the air temperature adjustment knob (D) to desired air temperature. Switching On and Off (Fig. 4) 1. Push the on/off switch (A) to the desired air flow settings: I:240 liter/min [122–752.F (50°C-400°C) ] A low air flow to heat up the workpiece slowly. II:450 liter/min [122–1112.F (50°C-600°C) ] A high air flow to heat up the workpiece quickly. 2. To turn the tool off, push the on/off switch (A) to Disconnect the tool from the power source and down before moving or storing it. 7 FIG. 4 A Stripping paint WARNING: Refer to Important Notice under Additional Safety Instructions for Heat Guns before using the tool remove paint. WARNING: Do not strip metal window frames as the heat may crack the glass. • When striping other window frames, use the glass protection nozzle. • To prevent igniting the surface, do not keep the tool directed at one spot too long. • Avoid collecting paint on the scraper accessory, as it may ignite. If necessary, carefully remove paint debris from the scraper accessory using a knife. 1. Attach the appropriate accessory. 2. Turn the air temperature adjustment knob (D) to high. 3. Turn the tool on by selecting the desired air flow. 4. Direct the hot air onto the paint to be removed. Best results will be achieved if the heat gun CONSTANTLY, from side to side to evenly NOT LINGER OR PAUSE IN ONE SPOT. English English English 5. When the paint softens, scrape the paint away using a hand scraper. REMEMBER: Splinters and small particles of stripped paint can be ignited and blown through holes and cracks in the surface being stripped. Stationary Use (Fig. 1) This tool can also be used in stationary mode. 1. Fold down the kickstand (C) as shown in Figure 1. 2. Set the tool onto a level, stable workbench. Ensure the tool will not tip over. 3. Secure the power cord to prevent entanglement or pulling the tool off the workbench. 4. Turn the tool on by selecting the desired air flow. Constant Heat Control (overloadprotection) When the tool is overloaded, this feature protects the heating element from damage without stopping the tool and/or without a cool down period 1. When the temperature gets too hot, the heating element switches itself off. The motor will continue to run and produce cold air. 2. When the temperature has cooled sufficiently (taking only a few seconds) the heating element will switch on automatically. Tool Ring (Fig. 1) WARNING: ALWAYS turn heat gun off, disconnect from the power source and let the tool cool down for at least 30 before moving or storing it. For easy storage, the tool can hang from the tool gun should be stored indoors. 8 Cool Down Period The nozzle and accessory becomes very hot during use. Turn heat gun off, disconnect from the power source and let the tool cool down for at least 30 minutes before moving or storing it. NOTE: To reduce the cooling time, switch the tool on at the lowest air temperature setting and let it run for a few minutes before turning the heat gun off. MAINTENANCE WARNING: To reduce the risk of injury, turn unit off and disconnect tool from power source before installing and removing accessories, before making any adjustments or removing/installing attachments or accessories. Your DEWALT power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Lubrication Your power tool requires no additional lubrication. Cleaning WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals weaken the materials used in these parts. Use a cloth only with water and mild soap. Never let any liquid tool; never immerse any part of the tool into a liquid. Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product. Recommended accessories for use with your...