Производитель: Haier
Размер: 2.01 mb
Название файла: 5d2ad775-c009-48b1-be76-ef606d344c08.pdf
![en en](/images/flag/s/en.gif)
![]() |
Фрагмент инструкции
If the washer has below 0 C, please be sure to ensure the washer is placed under the room temperature for 2~4 hours and then use . It is suggested to use foamless washing powder. Please put down the drain hose before washing and connect the water inlet pipe properly. Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children. Safety precautions Do not put any hot or heavy items ( such as the kettle with hot water ) on the washing machine. Do not decompose, repair or alter the machine by yourself. Handicapped or children without care shall not use the machine. Keep the machine away from direct sunlight and heat source like the heater. Do not wash laundries with volatile materials (such as thinner, petrol etc.). Petrol Thinner 3 Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. 4 Usage of the drain hose If the extra hose is too long, cut it either at point A or B. A B > 30mm <1.5m The drainage shall be smooth with the drain hose. 1.The height of the drain hose shall be less than 10cm , or the drainage will not be smooth enough and cause incomplete drainage. 2.Do not tramp or press the drain hose. 3.If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly. 4.If extra drain hose is needed , please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m. <10cm Voltage change This washer is assembled for 220V, but can be changed from 220V to 127V. Check your electrical source and follow the diagram below to convert voltage. (1). the safeguard bag to expose the connectors. (3). Detach the white connector from the green one(220V), then inlay it into the blue one(127V). (4). Pack all the connectors with the safeguard bag as usual and f Then install the back cover. Above all the steps must be done by the special serviceman. Loosen the fastening screw and take off the back cover. (2). Unknit ix it. Blue Green White Water inlet hose Water inlet Maximum Max Minimum Min Medium Med Water level indicator 5 How to change the direction of the drain hoses Install the water inlet hose; Select the water level Insert the water inlet hose into the water-filling entrance on the control pane directly.(pull it out to dismantle it) Select water level according to the quantity of the laundries. Set the water level adjusting lever to needed line. Figure 1 indicates the ex factory installation position of the drain hose. Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. Take off the drain hose from the cabinet. Take the hose out of the fixing groove. (See to Figure 2). Embed the drain hose into the groove along the side of the spin tub in the order of (1)~(3), heading for the side of the spin tub. (See to Figure 3). Embed the drain hose into the groove with hands. Take care not to damage the drain hose in fastening the fixing clamp. Figure 1 Extend the drain hose from the side of spin tub Figure 3 Embed into the groove in turn Extend to the spin tub side Soft item Back Front Soft item Figure 2 Install the lint filter After installation, please refer that the lint filter installed to the right station, otherwise the lint filter may be fallen off when washing, influencing your use. overflow filter lint filter Put the underside of the lint filter into overflow filter then push the upside into overflow filter. Preparation before washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put down the drain hose . 4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally. Pay attention to followings before washing the laundries Check if the laundriehas special requirement on washing s Clear the pocket. Take out the coins, sand, hairpinetc. s Tie the long strips; fasten the buttons; close zippers. The quantity of the laundries shall not be too large. Stretch and loosen the When the pulsator is running , the buttons of the laundries may cause noise. For laundries before the sake of putting them in discretion, please the tub. put the laundries with buttons into other laundries. a. Check if the laundries are applicable for washing with machine. b. Divide the laundries that are not colorfast from other laundries. c. Put those laundries difficult to absorb water into water with hand. d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil, please apply detergent on them in advance, which can make it easier to remove the soil. e. For those laundries that may get lint ball ...